W3cubDocs

/Ansible

cisco.iosxr.iosxr_ospfv2 – OSPFv2 resource module

Note

This plugin is part of the cisco.iosxr collection (version 2.5.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.iosxr.

To use it in a playbook, specify: cisco.iosxr.iosxr_ospfv2.

New in version 1.0.0: of cisco.iosxr

Synopsis
Parameters
Notes
Examples
Return Values

Synopsis

This module manages global OSPFv2 configuration on devices running Cisco IOS-XR

Note

This module has a corresponding action plugin.

Parameters

Parameter							Choices/Defaults	Comments
config dictionary								A list of OSPFv2 process configuration
	processes list / elements=dictionary							A list of OSPFv2 instances configuration
		address_family_unicast boolean					Choices: no yes	Enable unicast topology for ipv4 address family
		adjacency_stagger dictionary						Stagger OSPFv2 adjacency bring up
			disable boolean				Choices: no yes	Disable stagger OSPFv2 adjacency
			max_adjacency integer					Maximum simultaneous neighbors to bring up
			min_adjacency integer					Initial number of neighbors to bring up per area (default 2)
		apply_weight dictionary						Enable weights configured under interfaces for load sharing
			bandwidth integer					Reference bandwidth to use for calculation (Mbits/sec)
			default_weight integer					Specify default weight value to use when it is not configured under interface
		areas list / elements=dictionary						Configure OSPFv2 areas' properties
			area_id string / required					Area ID as IP address or integer
			authentication dictionary					Enable authentication
				keychain string				Specify keychain name
				message_digest dictionary				Use message-digest authentication
					keychain string			Specify keychain name
				no_auth boolean			Choices: no yes	Use no authentication
			authentication_key dictionary					Used to mention authentication password (key)
				clear string				Specifies an UNENCRYPTED password (key) will follow
				encrypted string				Specifies an ENCRYPTED password (key) will follow
				password string				The OSPFv2 password (key)
			bfd dictionary					Configure BFD parameters
				fast_detect dictionary				Configure fast detection
					set boolean		Choices: no yes	Enable fast detection only
					strict_mode boolean		Choices: no yes	Hold down neighbor session until BFD session is up
				minimum_interval integer				Hello interval in milli-seconds
				multiplier integer				Detect multiplier
			cost integer					Interface cost
			dead_interval integer					Interval after which a neighbor is declared dead
			default_cost integer					Set the summary default-cost of a NSSA/stub area. Stub's advertised external route metric
			hello_interval integer					Time between HELLO packets
			mpls dictionary					Configure MPLS routing protocol parameters
				ldp dictionary				Configure LDP parameters
					auto_config boolean		Choices: no yes	Enable LDP IGP interface auto-configuration
					sync boolean		Choices: no yes	Enable LDP IGP synchronization
					sync_igp_shortcuts boolean		Choices: no yes	LDP sync for igp-shortcut tunnels
				traffic_eng boolean			Choices: no yes	Configure an ospf area to run MPLS Traffic Engineering
			mtu_ignore string				Choices: enable disable	Enable/Disable ignoring of MTU in DBD packets
			nssa dictionary					NSSA settings for the area
				default_information_originate dictionary				Originate default Type 7 LSA
					metric integer			OSPFv2 default metric
					metric_type integer			Metric type for default routes
				no_redistribution boolean			Choices: no yes	Do not send redistributed LSAs into NSSA area
				no_summary boolean			Choices: no yes	Do not send summary LSAs into NSSA area
				set boolean			Choices: no yes	Configure area as NSSA
				translate dictionary				Translate LSA
					type7 dictionary			Translate from Type 7 to Type 5
						always boolean	Choices: no yes	Always translate LSAs
			ranges list / elements=dictionary					Summarize routes matching address/mask (border routers only)
				address string / required				IP in Prefix format (x.x.x.x/len)
				advertise boolean			Choices: no yes	Advertise this range (default)
				not_advertise boolean			Choices: no yes	DoNotAdvertise this range
			route_policy list / elements=dictionary					Specify the route-policy to filter type 3 LSAs (list can have one inbound and/or one outbound policy only)
				direction string			Choices: in out	Specify inbound or outbound
				parameters list / elements=string				Specify parameter values for the policy
			stub dictionary					Settings for configuring the area as a stub
				no_summary boolean			Choices: no yes	Do not send summary LSA into stub area
				set boolean			Choices: no yes	Configure the area as a stub
			transmit_delay integer					Estimated time needed to send link-state update packet
			virtual_link list / elements=dictionary					Define a virtual link
				authentication dictionary				Enable authentication
					keychain string			Specify keychain name
					message_digest dictionary			Use message-digest authentication
						keychain string		Specify keychain name
					no_auth boolean		Choices: no yes	Use no authentication
				authentication_key dictionary				Used to mention authentication password (key)
					clear string			Specifies an UNENCRYPTED password (key) will follow
					encrypted string			Specifies an ENCRYPTED password (key) will follow
					password string			The OSPFv2 password (key)
				dead_interval integer				Interval after which a neighbor is declared dead
				hello_interval integer				Time between HELLO packets
				id string / required				Router-ID of virtual link neighbor (A.B.C.D)
				message_digest_key dictionary				Message digest authentication password (key)
					id integer / required			Key ID (1-255)
					md5 dictionary			Use MD5 Algorithm
						clear boolean	Choices: no yes	Specifies an UNENCRYPTED password (key) will follow
						encrypted boolean	Choices: no yes	Specifies an ENCRYPTED password (key) will follow
						password string		The OSPFv2 password (key)
				retransmit_interval integer				Delay between LSA retransmissions
				transmit_delay integer				Link state transmit delay
		authentication dictionary						Enable authentication
			keychain string					Specify keychain name
			message_digest dictionary					Use message-digest authentication
				keychain string				Specify keychain name
				set boolean			Choices: no yes	Specify message-digest selection
			no_auth boolean				Choices: no yes	Use no authentication
		authentication_key dictionary						Used to mention authentication password (key)
			clear boolean				Choices: no yes	Specifies an UNENCRYPTED password (key) will follow
			encrypted boolean				Choices: no yes	Specifies an ENCRYPTED password (key) will follow
			password string					The OSPFv2 password (key)
		auto_cost dictionary						Calculate OSPFv2 interface cost according to bandwidth
			disable boolean				Choices: no yes	Assign OSPFv2 cost based on interface type
			reference_bandwidth integer					Specify reference bandwidth in megabits per sec
		bfd dictionary						Configure BFD parameters
			fast_detect dictionary					Configure fast detection
				set boolean			Choices: no yes	Enable fast detection only
				strict_mode boolean			Choices: no yes	Hold down neighbor session until BFD session is up
			minimum_interval integer					Hello interval in milli-seconds
			multiplier integer					Detect multiplier
		capability dictionary						Enable specific OSPFv2 feature
			opaque dictionary					Configure opaque LSA
				disable boolean			Choices: no yes	Disable Opaque LSA capability
				set boolean			Choices: no yes	Enable opaque LSA
			type7 string					NSSA capability
		cost integer						Interface cost (1-65535)
		database_filter string					Choices: enable disable	Filter OSPFv2 LSA during synchronization and flooding (all outgoing LSA). Enable/Disable filtering
		dead_interval integer						Interval after which a neighbor is declared dead
		default_information_originate dictionary						Distribute default route
			always boolean				Choices: no yes	Always advertise default route
			metric integer					OSPFv2 default metric
			metric_type integer					OSPFv2 metric type for default routes
			route_policy string					Apply route-policy to default-information origination
			set boolean				Choices: no yes	Enable distribution of default route
		default_metric integer						Set metric of redistributed routes
		demand_circuit string					Choices: enable disable	Enable/Disable OSPFv2 demand circuit
		distance dictionary						Define an administrative distance
			admin_distance list / elements=dictionary					Administrative distance
				access_list string				Access list name
				source string				Source IP address
				value integer				Distance value
				wildcard string				IP wild card bits (A.B.C.D)
			ospf_distance dictionary					OSPFv2 administrative distance
				external integer				Distance for external routes
				inter_area integer				Distance for inter-area routes
				intra_area integer				Distance for intra-area routes
		distribute_bgp_ls dictionary						Enable Distribution of LSAs to external services
			instance_id integer					Set distribution process instance identifier
			throttle integer					Throttle time between successive LSA updates
		distribute_link_state dictionary						Enable Distribution of LSAs to external services
			instance_id integer					Set distribution process instance identifier
			throttle integer					Throttle time between successive LSA updates
		distribute_list list / elements=dictionary						Filter networks in routing updates (list can have one inbound and/or one outbound policy only)
			access_list string					Inbound/outbound access-list
			direction string				Choices: in out	Filter incoming/outgoing routing updates
			outgoing_params dictionary					Specify additional parameters for outgoing updates only
				id string				For BGP, specify AS number. 2-byte AS number (or) 4-byte AS number in asdot (X.Y) format (or) 4-byte AS number in asplain format For OSPF, specify OSPFv2 instance name
				route_type string			Choices: bgp connected dagr ospf static	Type of routes
			route_policy string					Route Policy to filter OSPFv2 prefixes (for incoming updates only)
		external_out string					Choices: enable disable	Enable/Disable advertisement of intra-area prefixes as external
		flood_reduction string					Choices: enable disable	Enable/Disable OSPFv2 Flood Reduction
		hello_interval integer						Time between HELLO packets (<1-65535> seconds)
		ignore_lsa_mospf boolean					Choices: no yes	Do not complain upon receiving MOSPFv2 Type 6 LSA
		link_down_fast_detect boolean					Choices: no yes	Enable fast or early detection of link-down events
		log_adjacency_changes dictionary						Log adjacency state changes
			detail boolean				Choices: no yes	Log all state changes
			disable boolean				Choices: no yes	Disable log adjacency changes
			set boolean				Choices: no yes	Set log adjacency
		loopback_stub_network string					Choices: enable disable	Advertise loopback as a stub network
		max_lsa dictionary						Feature to limit the number of non-self-originated LSAs
			ignore_count integer					Set count on how many times adjacencies can be suppressed
			ignore_time integer					Set number of minutes during which all adjacencies are suppressed
			reset_time integer					Set number of minutes after which ignore-count is reset to zero
			threshold integer					Threshold value (%) at which to generate a warning message
			warning_only boolean				Choices: no yes	Log a warning message when limit is exceeded
		max_metric dictionary						Set maximum metric
			router_lsa dictionary					Maximum metric in self-originated router-LSAs
				external_lsa dictionary				External LSA configuration
					max_metric_value integer			Set max metric value for external LSAs
					set boolean		Choices: no yes	Set external-lsa attribute
				include_stub boolean			Choices: no yes	Advertise Max metric for Stub links as well
				on_startup dictionary				Effective only at startup
					set boolean		Choices: no yes	Set on-startup attribute
					wait_for_bgp_asn integer			ASN of BGP to wait for
					wait_period integer			Wait period in seconds after startup
				set boolean			Choices: no yes	Set router-lsa attribute
				summary_lsa dictionary				Summary LSAs configuration
					max_metric_value integer			Max metric value for summary LSAs
					set boolean		Choices: no yes	Set summary-lsa attribute
		message_digest_key dictionary						Message digest authentication password (key)
			id integer / required					Key ID
			md5 dictionary / required					Use MD5 Algorithm
				clear boolean			Choices: no yes	Specifies an UNENCRYPTED password (key) will follow
				encrypted boolean			Choices: no yes	Specifies an ENCRYPTED password (key) will follow
				password string				The OSPFv2 password (key)
		microloop_avoidance dictionary						Avoid microloops
			protected boolean				Choices: no yes	Avoid microloops for protected prefixes only)
			rib_update_delay integer					Delay to introduce between SPF and RIB updates
			segment_routing boolean				Choices: no yes	Enable segment routing microloop avoidance
		monitor_convergence dictionary						Enables OSPFv2 route convergence monitoring
			prefix_list string					Enables Individual Prefix Monitoring
			track_external_routes boolean				Choices: no yes	Enables Tracking External(Type-5/7) Prefix monitoring
			track_ip_frr boolean				Choices: no yes	Enables Tracking IP-Frr Convergence
			track_summary_routes boolean				Choices: no yes	Enables Tracking Summary(Inter-Area) Prefix monitoring
		mpls dictionary						Configure MPLS routing protocol parameters
			ldp dictionary					Configure LDP parameters
				auto_config boolean			Choices: no yes	Enable LDP IGP interface auto-configuration
				sync boolean			Choices: no yes	Enable LDP IGP synchronization
				sync_igp_shortcuts boolean			Choices: no yes	LDP sync for igp-shortcut tunnels
			traffic_eng dictionary					Routing protocol commands for MPLS Traffic Engineering
				autoroute_exclude dictionary				Exclude IP address destinations from using TE tunnels
					parameters list / elements=string			Specify parameter values for the policy
					route_policy string			Policy name
				igp_intact boolean			Choices: no yes	Retain one or more IPv4 nexthops with tunnel nexthops
				ldp_sync_update boolean			Choices: no yes	Enable LDP sync induced metric propagation
				multicast_intact boolean			Choices: no yes	Publish multicast-intact paths to RIB
				router_id string				Traffic Engineering stable IP address for system
		mtu_ignore string					Choices: enable disable	Enable/Disable ignoring of MTU in DBD packets
		network dictionary						Network type
			broadcast boolean				Choices: no yes	Specify OSPFv2 broadcast multi-access network
			non_broadcast boolean				Choices: no yes	Specify OSPFv2 NBMA network
			point_to_multipoint boolean				Choices: no yes	Specify OSPFv2 point-to-multipoint network
			point_to_point boolean				Choices: no yes	Specify OSPFv2 point-to-point network
		nsf dictionary						Non-stop forwarding
			cisco dictionary					Cisco Non-stop forwarding
				enforce_global boolean			Choices: no yes	Cancel NSF restart when non-NSF-aware neighbors detected for the whole OSPFv2 process
				set boolean			Choices: no yes	Enable Cisco NSF
			flush_delay_time integer					Maximum time allowed for external route learning
			ietf dictionary					IETF graceful restart
				helper_disable boolean			Choices: no yes	Disable router's helper support level
				set boolean			Choices: no yes	Only enable ietf option
			interval integer					Minimum interval between NSF restarts (<90-3600> seconds)
			lifetime integer					Maximum route lifetime following restart (<90-1800> seconds)
		nsr boolean					Choices: no yes	Enable NSR for all VRFs in this process. 'False' option to disable NSR for all VRFs in this process
		packet_size integer						Size of OSPFv2 packets to use. min=576 max=MTU bytes
		passive string					Choices: enable disable	Enable/Disable passive
		prefix_suppression dictionary						Suppress advertisement of the prefixes
			secondary_address boolean				Choices: no yes	Enable/Disable secondary address suppression
			set boolean				Choices: no yes	Set the suppression option
		priority integer						Router priority
		process_id string / required						The OSPFv2 Process ID
		protocol_shutdown dictionary						Protocol specific configuration
			host_mode boolean				Choices: no yes	Only traffic destined for this box allowed(cisco-support)
			limit dictionary					High watermark for incoming priority events
				high integer				Hello events are dropped when incoming event queue exceeds this value
				low integer				DBD/LS Update/Req packets are dropped when incoming event queue exceeds this value
				medium integer				LSA ACKs are dropped when incoming event queue exceeds this value
			on_reload boolean				Choices: no yes	Shutdown post reload only
			set boolean				Choices: no yes	Shutdown the OSPFv2 Protocol
		redistribute dictionary						Redistribute information from another routing Protocol
			id string					OnePK application name for application routes (or) AS number for bgp and eigrp (or) instance name for isis and ospf
			level integer				Choices: 1 2 12	ISIS levels
			lsa_type_summary boolean				Choices: no yes	LSA type 3 for redistributed routes
			match string					Redistribution of routes. For OSPFv2 - external/internal/nssa-external 1/2. For EIGRP - external/internal
			metric integer					Metric for redistributed routes
			metric_type integer				Choices: 1 2	OSPFv2 exterior metric type for redistributed routes
			nssa_only boolean				Choices: no yes	Redistribute to NSSA areas only
			preserve_med boolean				Choices: no yes	Preserve med of BGP routes
			route_policy dictionary					Apply route-policy to redistribution
				name string				Name of the policy
				parameters list / elements=string				Specify parameter values for the policy
			route_type string				Choices: application bgp connected dagr eigrp isis mobile ospf rip static subscriber	Route type to redistribute
			tag integer					Set tag for routes redistributed into OSPFv2
		retransmit_interval integer						Delay between LSA retransmissions
		router_id string						OSPFv2 router-id in IPv4 address format (A.B.C.D)
		security_ttl dictionary						Enable security
			hops integer					Maximum number of IP hops allowed <1-254>
			set boolean				Choices: no yes	Enable ttl security
		summary_in string					Choices: enable disable	Enable/Disable advertisement of external prefixes as inter-area
		summary_prefix list / elements=dictionary						Configure IP address summaries
			not_advertise boolean				Choices: no yes	Suppress routes that match the specified prefix/mask pair
			prefix string / required					IP summary address/mask (A.B.C.D/prefix)
			tag integer					Set tag
		timers dictionary						Configure timer related constants
			graceful_shutdown dictionary					Timers for graceful shutdown(cisco-support)
				initial_delay integer				Delay before starting graceful shutdown
				retain_routes integer				Time to keep routes active after graceful shutdown
			lsa dictionary					OSPFv2 global LSA timers
				group_pacing integer				OSPFv2 LSA group pacing timer. Interval between group of LSA being refreshed or maxaged
				min_arrival integer				OSPFv2 MinLSArrival timer. The minimum interval in millisec between accepting the same LSA
				refresh integer				OSPFv2 LSA refresh interval. How often self-originated LSAs should be refreshed, in seconds
			pacing_flood integer					OSPFv2 flood pacing timer. Interval in msec to pace flooding on all interfaces
			throttle dictionary					OSPFv2 throttle timers
				fast_reroute integer				Fast-reroute throttle timer. Delay between end of SPF and start of the fast-reroute computation in milliseconds
				lsa_all dictionary				LSA throttle timers for all types of OSPFv2 LSAs
					initial_delay integer			Delay to generate first occurance of LSA in milliseconds
					max_delay integer			Maximum delay between originating the same LSA in milliseconds
					min_delay integer			Minimum delay between originating the same LSA in milliseconds
				spf dictionary				OSPFv2 SPF throttle timers
					change_delay integer			Delay between receiving a change to SPF calculation in milliseconds
					max_wait integer			Maximum wait time in milliseconds for SPF calculations
					second_delay integer			Delay between first and second SPF calculation in milliseconds
		transmit_delay integer						Estimated time needed to send link-state update packet
		weight integer						Interface weight
running_config string								This option is used only with state parsed. The value of this option should be the output received from the IOS-XR device by executing the command show running-config router ospf. The state parsed reads the configuration from `running_config` option and transforms it into Ansible structured data as per the resource module's argspec and the value is then returned in the parsed key within the result.
state string							Choices: merged ← replaced deleted parsed gathered rendered overridden	The state the configuration should be left in.

Notes

Note

This module works with connection network_cli. See the IOS-XR Platform Options

Examples

# Using merged

# Before state:
# -------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 15:54:44.569 UTC
# % No such configuration item(s)
#

- name: Merge provided OSPFv2 configuration with the existing configuration
  cisco.iosxr.iosxr_ospfv2:
    config:
      processes:
      - process_id: '27'
        areas:
        - area_id: '10'
          hello_interval: 2
          authentication:
            keychain: ansi11393
      - process_id: '26'
        adjacency_stagger:
          max_adjacency: 20
          min_adjacency: 10
      - process_id: '10'
        authentication:
          keychain: ansible_test1102
        areas:
        - area_id: '11'
          default_cost: 5
          cost: 11
        - area_id: 22
          default_cost: 6
      - process_id: '30'
        areas:
        - area_id: 11
          default_cost: 5
        - area_id: 22
          default_cost: 6

        cost: 2
        default_metric: 10
        transmit_delay: 2
        hello_interval: 1
        dead_interval: 2
        retransmit_interval: 2
        weight: 2
        packet_size: 577
        priority: 1
        router_id: 2.2.2.2
        demand_circuit: enable
        passive: disable
        summary_in: enable
        flood_reduction: disable
        mtu_ignore: enable
        external_out: disable
    state: merged

#
#
# ------------------------
# Module Execution Result
# ------------------------
#
#  "before": {}
#
#  "commands": [
#        "router ospf 30",
#        "cost 2",
#        "weight 2",
#        "passive disable",
#        "priority 1",
#        "flood-reduction disable",
#        "default-metric 10",
#        "router-id 2.2.2.2",
#        "demand-circuit enable",
#        "packet-size 577",
#        "transmit-delay 2",
#        "summary-in enable",
#        "external-out disable",
#        "dead-interval 2",
#        "hello-interval 1",
#        "retransmit-interval 2",
#        "mtu-ignore enable",
#        "area 11 default-cost 5",
#        "area 22 default-cost 6",
#        "router ospf 26",
#        "adjacency stagger 10 20",
#        "authentication message-digest keychain ansible1101pass",
#        "router ospf 27",
#        "area 10 authentication keychain ansi11393",
#        "area 10 hello-interval 2",
#        "router ospf 10",
#        "authentication keychain ansible_test1102",
#        "area 11 default-cost 5",
#        "area 11 cost 11",
#        "area 22 default-cost 6"
#    ]
#
#  "after": {
#        "processes": [
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "cost": 11,
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "authentication": {
#                    "keychain": "ansible_test1102"
#                },
#                "process_id": "10"
#            },
#            {
#                "adjacency_stagger": {
#                    "max_adjacency": 20,
#                    "min_adjacency": 10
#                },
#                "authentication": {
#                    "message_digest": {
#                        "keychain": "ansible1101pass"
#                    }
#                },
#                "process_id": "26"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "10",
#                        "authentication": {
#                            "keychain": "ansi11393"
#                        },
#                        "hello_interval": 2
#                    }
#                ],
#                "process_id": "27"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "cost": 2,
#                "dead_interval": 2,
#                "default_metric": 10,
#                "demand_circuit": "enable",
#                "external_out": "disable",
#                "flood_reduction": "disable",
#                "hello_interval": 1,
#                "mtu_ignore": "enable",
#                "packet_size": 577,
#                "passive": "disable",
#                "priority": 1,
#                "process_id": "30",
#                "retransmit_interval": 2,
#                "router_id": "2.2.2.2",
#                "summary_in": "enable",
#                "transmit_delay": 2,
#                "weight": 2
#            }
#        ]
#    }
#
#
# ------------
# After state
# ------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:06:44.406 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  authentication message-digest keychain ansible1101pass
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#  authentication keychain ansi11393
#   hello-interval 2
# !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
#


# Using replaced
#
# ------------
# Before state
# ------------
#
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:06:44.406 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  authentication message-digest keychain ansible1101pass
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#  authentication keychain ansi11393
#   hello-interval 2
# !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
#

- name: Replace OSPFv2 routes configurations from the device
  cisco.iosxr.iosxr_ospfv2:
    config:
      processes:
      - process_id: 27
        areas:
        - area_id: 10
          hello_interval: 2
        - area_id: 20
          cost: 2
          default_cost: 2
          authentication:
            keychain: ansi11393
      - process_id: 26
        adjacency_stagger:
          min_adjacency: 10
          max_adjacency: 20
    state: replaced

#
#
# ------------------------
# Module Execution Result
# ------------------------
#
#  "before": {
#        "processes": [
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "cost": 11,
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "authentication": {
#                    "keychain": "ansible_test1102"
#                },
#                "process_id": "10"
#            },
#            {
#                "adjacency_stagger": {
#                    "max_adjacency": 20,
#                    "min_adjacency": 10
#                },
#                "authentication": {
#                    "message_digest": {
#                        "keychain": "ansible1101pass"
#                    }
#                },
#                "process_id": "26"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "10",
#                        "authentication": {
#                            "keychain": "ansi11393"
#                        },
#                        "hello_interval": 2
#                    }
#                ],
#                "process_id": "27"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "cost": 2,
#                "dead_interval": 2,
#                "default_metric": 10,
#                "demand_circuit": "enable",
#                "external_out": "disable",
#                "flood_reduction": "disable",
#                "hello_interval": 1,
#                "mtu_ignore": "enable",
#                "packet_size": 577,
#                "passive": "disable",
#                "priority": 1,
#                "process_id": "30",
#                "retransmit_interval": 2,
#                "router_id": "2.2.2.2",
#                "summary_in": "enable",
#                "transmit_delay": 2,
#                "weight": 2
#            }
#        ]
#    }
#
#  "commands": [
#        "router ospf 27",
#        "no area 10 authentication keychain ansi11393",
#        "area 20 authentication keychain ansi11393",
#        "area 20 default-cost 2",
#        "area 20 cost 2"
#    ]
#
#  "after": {
#        "processes": [
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "cost": 11,
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "authentication": {
#                    "keychain": "ansible_test1102"
#                },
#                "process_id": "10"
#            },
#            {
#                "adjacency_stagger": {
#                    "max_adjacency": 20,
#                    "min_adjacency": 10
#                },
#                "authentication": {
#                    "message_digest": {
#                        "keychain": "ansible1101pass"
#                    }
#                },
#                "process_id": "26"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "10",
#                        "hello_interval": 2
#                    },
#                    {
#                        "area_id": "20",
#                        "authentication": {
#                            "keychain": "ansi11393"
#                        },
#                        "cost": 2,
#                        "default_cost": 2
#                    }
#                ],
#                "process_id": "27"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "cost": 2,
#                "dead_interval": 2,
#                "default_metric": 10,
#                "demand_circuit": "enable",
#                "external_out": "disable",
#                "flood_reduction": "disable",
#                "hello_interval": 1,
#                "mtu_ignore": "enable",
#                "packet_size": 577,
#                "passive": "disable",
#                "priority": 1,
#                "process_id": "30",
#                "retransmit_interval": 2,
#                "router_id": "2.2.2.2",
#                "summary_in": "enable",
#                "transmit_delay": 2,
#                "weight": 2
#            }
#        ]
#    }
#
#
# -----------
# After state
# -----------
#
# RP/0/RP0/CPU0:anton(config)#do show running-config router ospf
# Thu Jun 11 16:40:31.038 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  authentication message-digest keychain ansible1101pass
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#   hello-interval 2
#  !
#  area 20
#   cost 2
#   authentication keychain ansi11393
#   default-cost 2
#  !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
#


# Using overridden
#
# ------------
# Before state
# ------------
#
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:06:44.406 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  authentication message-digest keychain ansible1101pass
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#  authentication keychain ansi11393
#   hello-interval 2
# !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
#

- name: Override existing OSPFv2 configurations from the device
  cisco.iosxr.iosxr_ospfv2:
    config:
      processes:
      - process_id: 27
        areas:
        - area_id: 10
          hello_interval: 2
          authentication:
            keychain: ansi11393
        - area_id: 20
          cost: 2
          default_cost: 2
          authentication:
            keychain: ansi11393
      - process_id: 26
        adjacency_stagger:
          min_adjacency: 10
          max_adjacency: 20
    state: overridden

#
#
# ------------------------
# Module Execution Result
# ------------------------
#
#  "before": {
#        "processes": [
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "cost": 11,
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "authentication": {
#                    "keychain": "ansible_test1102"
#                },
#                "process_id": "10"
#            },
#            {
#                "adjacency_stagger": {
#                    "max_adjacency": 20,
#                    "min_adjacency": 10
#                },
#                "authentication": {
#                    "message_digest": {
#                        "keychain": "ansible1101pass"
#                    }
#                },
#                "process_id": "26"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "10",
#                        "authentication": {
#                            "keychain": "ansi11393"
#                        },
#                        "hello_interval": 2
#                    }
#                ],
#                "process_id": "27"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "cost": 2,
#                "dead_interval": 2,
#                "default_metric": 10,
#                "demand_circuit": "enable",
#                "external_out": "disable",
#                "flood_reduction": "disable",
#                "hello_interval": 1,
#                "mtu_ignore": "enable",
#                "packet_size": 577,
#                "passive": "disable",
#                "priority": 1,
#                "process_id": "30",
#                "retransmit_interval": 2,
#                "router_id": "2.2.2.2",
#                "summary_in": "enable",
#                "transmit_delay": 2,
#                "weight": 2
#            }
#        ]
#    }
#
#  "commands": [
#        "router ospf 10",
#        "no authentication keychain ansible_test1102",
#        "no area 11 default-cost 5",
#        "no area 11 cost 11",
#        "no area 22 default-cost 6",
#        "router ospf 30",
#        "no cost 2",
#        "no weight 2",
#        "no passive disable",
#        "no priority 1",
#        "no flood-reduction disable",
#        "no default-metric 10",
#        "no router-id 2.2.2.2",
#        "no demand-circuit enable",
#        "no packet-size 577",
#        "no transmit-delay 2",
#        "no summary-in enable",
#        "no external-out disable",
#        "no dead-interval 2",
#        "no hello-interval 1",
#        "no retransmit-interval 2",
#        "no mtu-ignore enable",
#        "no area 11 default-cost 5",
#        "no area 22 default-cost 6",
#        "router ospf 27",
#        "area 20 authentication keychain ansi11393",
#        "area 20 default-cost 2",
#        "area 20 cost 2"
#    ]
#
#  "after": {
#        "processes": [
#            {
#                "process_id": "10"
#            },
#            {
#                "adjacency_stagger": {
#                    "max_adjacency": 20,
#                    "min_adjacency": 10
#                },
#                "authentication": {
#                    "message_digest": {
#                        "keychain": "ansible1101pass"
#                    }
#                },
#                "process_id": "26"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "10",
#                        "authentication": {
#                            "keychain": "ansi11393"
#                        },
#                        "hello_interval": 2
#                    },
#                    {
#                        "area_id": "20",
#                        "authentication": {
#                            "keychain": "ansi11393"
#                        },
#                        "cost": 2,
#                        "default_cost": 2
#                    }
#                ],
#                "process_id": "27"
#            },
#            {
#                "process_id": "30"
#            }
#        ]
#    }
#
#
# -----------
# After state
# -----------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:50:36.332 UTC
# router ospf 10
# !
# router ospf 26
#  authentication message-digest keychain ansible1101pass
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#   authentication keychain ansi11393
#   hello-interval 2
#  !
#  area 20
#   cost 2
#   authentication keychain ansi11393
#   default-cost 2
#  !
# !
# router ospf 30
# !
#


# Using deleted
#
# ------------
# Before state
# ------------
#
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:06:44.406 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  authentication message-digest keychain ansible1101pass
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#  authentication keychain ansi11393
#   hello-interval 2
# !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
#

- name: Deleted existing OSPFv2 configurations from the device
  cisco.iosxr.iosxr_ospfv2:
    config:
      processes:
      - process_id: '10'
      - process_id: '26'
      - process_id: '27'
      - process_id: '30'
    state: deleted

#
#
# ------------------------
# Module Execution Result
# ------------------------
#
#  "before": {
#        "processes": [
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "cost": 11,
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "authentication": {
#                    "keychain": "ansible_test1102"
#                },
#                "process_id": "10"
#            },
#            {
#                "adjacency_stagger": {
#                    "max_adjacency": 20,
#                    "min_adjacency": 10
#                },
#                "authentication": {
#                    "message_digest": {
#                        "keychain": "ansible1101pass"
#                    }
#                },
#                "process_id": "26"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "10",
#                        "authentication": {
#                            "keychain": "ansi11393"
#                        },
#                        "hello_interval": 2
#                    }
#                ],
#                "process_id": "27"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "cost": 2,
#                "dead_interval": 2,
#                "default_metric": 10,
#                "demand_circuit": "enable",
#                "external_out": "disable",
#                "flood_reduction": "disable",
#                "hello_interval": 1,
#                "mtu_ignore": "enable",
#                "packet_size": 577,
#                "passive": "disable",
#                "priority": 1,
#                "process_id": "30",
#                "retransmit_interval": 2,
#                "router_id": "2.2.2.2",
#                "summary_in": "enable",
#                "transmit_delay": 2,
#                "weight": 2
#            }
#        ]
#    },
#
#  "commands": [
#        "router ospf 10",
#        "no authentication keychain ansible_test1102",
#        "no area 11 default-cost 5",
#        "no area 11 cost 11",
#        "no area 22 default-cost 6",
#        "router ospf 26",
#        "no adjacency stagger 10 20",
#        "no authentication message-digest keychain ansible1101pass",
#        "router ospf 27",
#        "no area 10 authentication keychain ansi11393",
#        "no area 10 hello-interval 2",
#        "router ospf 30",
#        "no cost 2",
#        "no weight 2",
#        "no passive disable",
#        "no priority 1",
#        "no flood-reduction disable",
#        "no default-metric 10",
#        "no router-id 2.2.2.2",
#        "no demand-circuit enable",
#        "no packet-size 577",
#        "no transmit-delay 2",
#        "no summary-in enable",
#        "no external-out disable",
#        "no dead-interval 2",
#        "no hello-interval 1",
#        "no retransmit-interval 2",
#        "no mtu-ignore enable",
#        "no area 11 default-cost 5",
#        "no area 22 default-cost 6"
#    ]
#
#  "after": {
#        "processes": [
#            {
#                "process_id": "10"
#            },
#            {
#                "process_id": "26"
#            },
#            {
#                "process_id": "27"
#            },
#            {
#                "process_id": "30"
#            }
#        ]
#    }
#
#
# -----------
# After state
# -----------
#
# RP/0/RP0/CPU0:anton(config)#show running-config router ospf
# Thu Jun 11 17:07:34.218 UTC
# router ospf 10
# !
# router ospf 26
# !
# router ospf 27
# !
# router ospf 30
# !


# Using parsed
# parsed.cfg
# ------------
# Thu Jun 11 17:28:51.918 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  authentication message-digest keychain ansible1101pass
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#   authentication keychain ansi11393
#   hello-interval 2
#  !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
- name: Parsed the device configuration to get output commands
  cisco.iosxr.iosxr_ospfv2:
    running_config: "{{ lookup('file', './parsed.cfg') }}"
    state: parsed
#
#
# -------------------------
# Module Execution Result
# -------------------------
#
#
# "parsed": {
#        "processes": [
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "cost": 11,
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "authentication": {
#                    "keychain": "ansible_test1102"
#                },
#                "process_id": "10"
#            },
#            {
#                "adjacency_stagger": {
#                    "max_adjacency": 20,
#                    "min_adjacency": 10
#                },
#                "authentication": {
#                    "message_digest": {
#                        "keychain": "ansible1101pass"
#                    }
#                },
#                "process_id": "26"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "10",
#                        "authentication": {
#                            "keychain": "ansi11393"
#                        },
#                        "hello_interval": 2
#                    }
#                ],
#                "process_id": "27"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "cost": 2,
#                "dead_interval": 2,
#                "default_metric": 10,
#                "demand_circuit": "enable",
#                "external_out": "disable",
#                "flood_reduction": "disable",
#                "hello_interval": 1,
#                "mtu_ignore": "enable",
#                "packet_size": 577,
#                "passive": "disable",
#                "priority": 1,
#                "process_id": "30",
#                "retransmit_interval": 2,
#                "router_id": "2.2.2.2",
#                "summary_in": "enable",
#                "transmit_delay": 2,
#                "weight": 2
#            }
#        ]
#    }



# Using rendered
#
#
- name: Render the commands for provided  configuration
  cisco.iosxr.iosxr_ospfv2:
    config:
      processes:
      - process_id: 27
        areas:
        - area_id: 10
          hello_interval: 2
          authentication:
            keychain: ansi11393
      - process_id: 26
        adjacency_stagger:
          min_adjacency: 10
          max_adjacency: 20
      - process_id: 10
        authentication:
          keychain: ansible_test1102
        areas:
        - area_id: 11
          default_cost: 5
          cost: 11
        - area_id: 22
          default_cost: 6
      - process_id: 30
        areas:
        - area_id: 11
          default_cost: 5
        - area_id: 22
          default_cost: 6

        cost: 2
        default_metric: 10
        transmit_delay: 2
        hello_interval: 1
        dead_interval: 2
        retransmit_interval: 2
        weight: 2
        packet_size: 577
        priority: 1
        router_id: 2.2.2.2
        demand_circuit: enable
        passive: disable
        summary_in: enable
        flood_reduction: disable
        mtu_ignore: enable
        external_out: disable
    state: rendered

#
#
# -------------------------
# Module Execution Result
# -------------------------
#
#
# "rendered": [
#        "router ospf 27",
#        "area 10 authentication keychain ansi11393",
#        "area 10 hello-interval 2",
#        "router ospf 26",
#        "adjacency stagger 10 20",
#        "authentication message-digest keychain ansible1101pass",
#        "router ospf 10",
#        "authentication keychain ansible_test1102",
#        "area 11 default-cost 5",
#        "area 11 cost 11",
#        "area 22 default-cost 6",
#        "router ospf 30",
#        "cost 2",
#        "weight 2",
#        "passive disable",
#        "priority 1",
#        "flood-reduction disable",
#        "default-metric 10",
#        "router-id 2.2.2.2",
#        "demand-circuit enable",
#        "packet-size 577",
#        "transmit-delay 2",
#        "summary-in enable",
#        "external-out disable",
#        "dead-interval 2",
#        "hello-interval 1",
#        "retransmit-interval 2",
#        "mtu-ignore enable",
#        "area 11 default-cost 5",
#        "area 22 default-cost 6"
#    ]


# Using gathered
#
# Before state:
# -------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:06:44.406 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  authentication message-digest keychain ansible1101pass
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#  authentication keychain ansi11393
#   hello-interval 2
# !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
#
- name: Gather ospfv2 routes configuration
  cisco.iosxr.iosxr_ospfv2:
    state: gathered
#
#
# -------------------------
# Module Execution Result
# -------------------------
#
#    "gathered": {
#        "processes": [
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "cost": 11,
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "authentication": {
#                    "keychain": "ansible_test1102"
#                },
#                "process_id": "10"
#            },
#            {
#                "adjacency_stagger": {
#                    "max_adjacency": 20,
#                    "min_adjacency": 10
#                },
#                "authentication": {
#                    "message_digest": {
#                        "keychain": "ansible1101pass"
#                    }
#                },
#                "process_id": "26"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "10",
#                        "authentication": {
#                            "keychain": "ansi11393"
#                        },
#                        "hello_interval": 2
#                    }
#                ],
#                "process_id": "27"
#            },
#            {
#                "areas": [
#                    {
#                        "area_id": "11",
#                        "default_cost": 5
#                    },
#                    {
#                        "area_id": "22",
#                        "default_cost": 6
#                    }
#                ],
#                "cost": 2,
#                "dead_interval": 2,
#                "default_metric": 10,
#                "demand_circuit": "enable",
#                "external_out": "disable",
#                "flood_reduction": "disable",
#                "hello_interval": 1,
#                "mtu_ignore": "enable",
#                "packet_size": 577,
#                "passive": "disable",
#                "priority": 1,
#                "process_id": "30",
#                "retransmit_interval": 2,
#                "router_id": "2.2.2.2",
#                "summary_in": "enable",
#                "transmit_delay": 2,
#                "weight": 2
#            }
#        ]
#    }
#
# After state:
# -------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:06:44.406 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  authentication message-digest keychain ansible1101pass
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#  authentication keychain ansi11393
#   hello-interval 2
# !
# !
# router ospf 30
# router-id 2.2.2.2
# summary-in enable
# external-out disable
# cost 2
# packet-size 577
# weight 2
# passive disable
# priority 1
# mtu-ignore enable
# flood-reduction disable
# dead-interval 2
# retransmit-interval 2
# demand-circuit enable
# hello-interval 1
# transmit-delay 2
# default-metric 10
# area 11
#  default-cost 5
# !
# area 22
#  default-cost 6
# !
# !
#
#

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
after dictionary	when changed	The resulting configuration model invocation. Sample: The configuration returned will always be in the same format of the parameters above.
before dictionary	always	The configuration prior to the model invocation. Sample: The configuration returned will always be in the same format of the parameters above.
commands list / elements=string	always	The set of commands pushed to the remote device. Sample: ['router ospf 30', "authentication message-digest keychain 'ansible1101pass'"]

Authors

Rohit Thakur (@rohitthakur2590)

© 2012–2018 Michael DeHaan
© 2018–2021 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/latest/collections/cisco/iosxr/iosxr_ospfv2_module.html