Note
This plugin is part of the f5networks.f5_modules collection (version 1.12.0).
You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.
To install it, use: ansible-galaxy collection install f5networks.f5_modules.
To use it in a playbook, specify: f5networks.f5_modules.bigip_monitor_icmp.
New in version 1.1.0: of f5networks.f5_modules
| Parameter | Choices/Defaults | Comments | |
|---|---|---|---|
| adaptive boolean |
| Specifies whether adaptive response time monitoring is enabled for this monitor. When yes, the monitor determines the state of a service based on how divergent from the mean latency a monitor probe for that service is allowed to be. Also, values for the allowed_divergence, adaptive_limit, and and sampling_timespan will be enforced.When disabled, the monitor determines the state of a service based on the interval, up_interval, time_until_up, and timeout monitor settings. | |
| adaptive_limit integer | Specifies the absolute number of milliseconds that may not be exceeded by a monitor probe, regardless of allowed_divergence setting, for a probe to be considered successful.This value applies regardless of the value of the allowed_divergence setting.While this value can be configured when adaptive is no, it will not take effect on the system until adaptive is yes. | ||
| allowed_divergence_type string |
| When specifying a new monitor, if adaptive is yes, the default is relative.When absolute, the number of milliseconds the latency of a monitor probe can exceed the mean latency of a monitor probe for the service being probed. In typical cases, if the monitor detects three probes in a row that miss the latency value you set, the pool member or node is marked down.When relative, the percentage of deviation the latency of a monitor probe can exceed the mean latency of a monitor probe for the service being probed. | |
| allowed_divergence_value integer | When specifying a new monitor, if adaptive is yes, and type is relative, the default is 25 percent. | ||
| app_service string | The iApp service to be associated with this profile. When no service is specified, the default is None. | ||
| description string | The description of the monitor. | ||
| interval integer | Specifies the frequency, in seconds, at which the system issues the monitor check when either the resource is down or the status of the resource is unknown. | ||
| ip string | Specifies the IP address of the resource that is the destination of this monitor. When set to *, the device performs a health check on the IP address of the node. When set to an <IP> the device performs a health check on that IP address and marks the associated node up or down as a result of the response. This option is set by the device by default when not defined during monitor creation. When set to an <IP> and transparent is yes, the device performs a health check on that IP address, routes the check through the associated node IP address, and marks the associated node IP address up or down accordingly. | ||
| manual_resume boolean |
| Specifies whether the system automatically changes the status of a resource to enabled at the next successful monitor check. If you set this option to yes, you must manually re-enable the resource before the system can use it for load balancing connections.When yes, specifies you must manually re-enable the resource after an unsuccessful monitor check.When no, specifies the system automatically changes the status of a resource to enabled at the next successful monitor check. | |
| name string / required | Specifies the name of the monitor. | ||
| parent string | The parent template of this monitor template. Once this value has been set, it cannot be changed. When creating a new monitor, if this parameter is not specified, the default is the system-supplied icmp monitor. | ||
| partition string | Default: "Common" | Device partition to manage resources on. | |
| provider dictionary added in 1.0.0 of f5networks.f5_modules | A dict object containing connection details. | ||
| auth_provider string | Configures the auth provider for to obtain authentication tokens from the remote device. This option is really used when working with BIG-IQ devices. | ||
| no_f5_teem boolean |
| If yes, TEEM telemetry data is not sent to F5.You may omit this option by setting the environment variable F5_TELEMETRY_OFF.Previously used variable F5_TEEM is deprecated as its name was confusing. | |
| password string / required | The password for the user account used to connect to the BIG-IP. You may omit this option by setting the environment variable F5_PASSWORD.aliases: pass, pwd | ||
| server string / required | The BIG-IP host. You may omit this option by setting the environment variable F5_SERVER. | ||
| server_port integer | Default: 443 | The BIG-IP server port. You may omit this option by setting the environment variable F5_SERVER_PORT. | |
| timeout integer | Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error. | ||
| transport string |
| Configures the transport connection to use when connecting to the remote device. | |
| user string / required | The username to connect to the BIG-IP with. This user must have administrative privileges on the device. You may omit this option by setting the environment variable F5_USER. | ||
| validate_certs boolean |
| If no, SSL certificates are not validated. Use this only on personally controlled sites using self-signed certificates.You may omit this option by setting the environment variable F5_VALIDATE_CERTS. | |
| sampling_timespan integer | Specifies the length, in seconds, of the probe history window the system uses to calculate the mean latency and standard deviation of a monitor probe. While this value can be configured when adaptive is no, it will not take effect on the system until adaptive is yes. | ||
| state string |
| When present, ensures that the monitor exists.When absent, ensures the monitor is removed. | |
| time_until_up integer | Specifies the number of seconds to wait after a resource first responds correctly to the monitor before setting the resource to 'up'. During the interval, all responses from the resource must be correct. When the interval expires, the resource is marked 'up'. A value of 0 means the resource is marked up immediately upon receipt of the first correct response. | ||
| timeout integer | Specifies the number of seconds the target has in which to respond to the monitor request. If the target responds within the set time period, it is considered 'up'. If the target does not respond within the set time period, it is considered 'down'. When this value is set to 0 (zero), the system uses the interval from the parent monitor. Note that timeout and time_until_up combine to control when a resource is set to up. | ||
| transparent boolean |
| Specifies whether the monitor operates in transparent mode. A monitor in transparent mode directs traffic through the associated pool members or nodes (usually a router or firewall) to the aliased destination (that is, it probes the ip-port combination specified in the monitor).If the monitor cannot successfully reach the aliased destination, the pool member or node through which the monitor traffic was sent is marked down. When creating a new monitor, if this parameter is not provided, the default value will be whatever is provided by the parent. | |
| up_interval integer | Specifies the interval for the system to use to perform the health check when a resource is up. When 0, specifies the system uses the interval specified in interval to check the health of the resource.When any other number, enables you to specify a different interval to use when checking the health of a resource that is up. | ||
Note
- name: Create an ICMP monitor
bigip_monitor_icmp:
name: icmp1
adaptive: no
interval: 1
time_until_up: 0
timeout: 3
provider:
password: secret
server: lb.mydomain.com
user: admin
delegate_to: localhost
- name: Update an ICMP monitor
bigip_monitor_icmp:
name: icmp1
manual_resume: yes
interval: 5
provider:
password: secret
server: lb.mydomain.com
user: admin
delegate_to: localhost
- name: Remove an ICMP monitor
bigip_monitor_icmp:
name: icmp1
state: absent
provider:
password: secret
server: lb.mydomain.com
user: admin
delegate_to: localhost
Common return values are documented here, the following are the fields unique to this module:
| Key | Returned | Description |
|---|---|---|
| adaptive boolean | changed | Whether adaptive is enabled or not. Sample: True |
| adaptive_limit integer | changed | Absolute number of milliseconds that may not be exceeded by a monitor probe. Sample: 200 |
| allowed_divergence_type string | changed | Type of divergence used for adaptive response time monitoring. Sample: absolute |
| allowed_divergence_value integer | changed | Value of the type of divergence used for adaptive response time monitoring. May be percent or ms depending on whether relative or absolute.Sample: 25 |
| app_service string | changed | The iApp service associated with this monitor. Sample: /Common/good_service.app/good_service |
| description string | changed | The description of the monitor. Sample: Important Monitor |
| interval integer | changed | The new interval in which to run the monitor check. Sample: 2 |
| ip string | changed | The new IP of IP/port definition. Sample: 10.12.13.14 |
| parent string | changed | New parent template of the monitor. Sample: gateway-icmp |
| port string | changed | Alias port or service for the monitor to check, on behalf of the pools or pool members with which the monitor is associated. Sample: 80 |
| sampling_timespan integer | changed | Absolute number of milliseconds that may not be exceeded by a monitor probe. Sample: 200 |
| time_until_up integer | changed | The new time in which to mark a system as up after first successful response. Sample: 2 |
| timeout integer | changed | The new timeout in which the remote system must respond to the monitor. Sample: 10 |
| transparent boolean | changed | Whether the monitor operates in transparent mode. |
| up_interval integer | changed | Interval for the system to use to perform the health check when a resource is up. |
© 2012–2018 Michael DeHaan
© 2018–2021 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/latest/collections/f5networks/f5_modules/bigip_monitor_icmp_module.html