Note
This plugin is part of the fortinet.fortios collection (version 2.1.2).
You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.
To install it, use: ansible-galaxy collection install fortinet.fortios.
To use it in a playbook, specify: fortinet.fortios.fortios_system_global.
New in version 2.10: of fortinet.fortios
The below requirements are needed on the host that executes this module.
| Parameter | Choices/Defaults | Comments | |
|---|---|---|---|
| access_token string | Token-based authentication. Generated from GUI of Fortigate. | ||
| enable_log boolean |
| Enable/Disable logging for task. | |
| system_global dictionary | Configure global attributes. | ||
| admin_concurrent string |
| Enable/disable concurrent administrator logins. (Use policy-auth-concurrent for firewall authenticated users.) | |
| admin_console_timeout integer | Console login timeout that overrides the admintimeout value. (15 - 300 seconds) (15 seconds to 5 minutes). 0 the default, disables this timeout. | ||
| admin_forticloud_sso_login string |
| Enable/disable FortiCloud admin login via SSO. | |
| admin_hsts_max_age integer | HTTPS Strict-Transport-Security header max-age in seconds. A value of 0 will reset any HSTS records in the browser.When admin-https-redirect is disabled the header max-age will be 0. | ||
| admin_https_pki_required string |
| Enable/disable admin login method. Enable to force administrators to provide a valid certificate to log in if PKI is enabled. Disable to allow administrators to log in with a certificate or password. | |
| admin_https_redirect string |
| Enable/disable redirection of HTTP administration access to HTTPS. | |
| admin_https_ssl_versions list / elements=string |
| Allowed TLS versions for web administration. | |
| admin_lockout_duration integer | Amount of time in seconds that an administrator account is locked out after reaching the admin-lockout-threshold for repeated failed login attempts. | ||
| admin_lockout_threshold integer | Number of failed login attempts before an administrator account is locked out for the admin-lockout-duration. | ||
| admin_login_max integer | Maximum number of administrators who can be logged in at the same time (1 - 100) | ||
| admin_maintainer string |
| Enable/disable maintainer administrator login. When enabled, the maintainer account can be used to log in from the console after a hard reboot. The password is "bcpb" followed by the FortiGate unit serial number. You have limited time to complete this login. | |
| admin_port integer | Administrative access port for HTTP. (1 - 65535). | ||
| admin_restrict_local string |
| Enable/disable local admin authentication restriction when remote authenticator is up and running. | |
| admin_scp string |
| Enable/disable using SCP to download the system configuration. You can use SCP as an alternative method for backing up the configuration. | |
| admin_server_cert string | Server certificate that the FortiGate uses for HTTPS administrative connections. Source certificate.local.name. | ||
| admin_sport integer | Administrative access port for HTTPS. (1 - 65535). | ||
| admin_ssh_grace_time integer | Maximum time in seconds permitted between making an SSH connection to the FortiGate unit and authenticating (10 - 3600 sec (1 hour)). | ||
| admin_ssh_password string |
| Enable/disable password authentication for SSH admin access. | |
| admin_ssh_port integer | Administrative access port for SSH. (1 - 65535). | ||
| admin_ssh_v1 string |
| Enable/disable SSH v1 compatibility. | |
| admin_telnet string |
| Enable/disable TELNET service. | |
| admin_telnet_port integer | Administrative access port for TELNET. (1 - 65535). | ||
| admintimeout integer | Number of minutes before an idle administrator session times out (5 - 480 minutes (8 hours)). A shorter idle timeout is more secure. | ||
| alias string | Alias for your FortiGate unit. | ||
| allow_traffic_redirect string |
| Disable to allow traffic to be routed back on a different interface. | |
| anti_replay string |
| Level of checking for packet replay and TCP sequence checking. | |
| arp_max_entry integer | Maximum number of dynamically learned MAC addresses that can be added to the ARP table (131072 - 2147483647). | ||
| asymroute string |
| Enable/disable asymmetric route. | |
| auth_cert string | Server certificate that the FortiGate uses for HTTPS firewall authentication connections. Source certificate.local.name. | ||
| auth_http_port integer | User authentication HTTP port. (1 - 65535). | ||
| auth_https_port integer | User authentication HTTPS port. (1 - 65535). | ||
| auth_keepalive string |
| Enable to prevent user authentication sessions from timing out when idle. | |
| auth_session_limit string |
| Action to take when the number of allowed user authenticated sessions is reached. | |
| auto_auth_extension_device string |
| Enable/disable automatic authorization of dedicated Fortinet extension devices. | |
| autorun_log_fsck string |
| Enable/disable automatic log partition check after ungraceful shutdown. | |
| av_affinity string | Affinity setting for AV scanning (hexadecimal value up to 256 bits in the format of xxxxxxxxxxxxxxxx). | ||
| av_failopen string |
| Set the action to take if the FortiGate is running low on memory or the proxy connection limit has been reached. | |
| av_failopen_session string |
| When enabled and a proxy for a protocol runs out of room in its session table, that protocol goes into failopen mode and enacts the action specified by av-failopen. | |
| batch_cmdb string |
| Enable/disable batch mode, allowing you to enter a series of CLI commands that will execute as a group once they are loaded. | |
| block_session_timer integer | Duration in seconds for blocked sessions (1 - 300 sec (5 minutes)). | ||
| br_fdb_max_entry integer | Maximum number of bridge forwarding database (FDB) entries. | ||
| cert_chain_max integer | Maximum number of certificates that can be traversed in a certificate chain. | ||
| cfg_revert_timeout integer | Time-out for reverting to the last saved configuration. | ||
| cfg_save string |
| Configuration file save mode for CLI changes. | |
| check_protocol_header string |
| Level of checking performed on protocol headers. Strict checking is more thorough but may affect performance. Loose checking is ok in most cases. | |
| check_reset_range string |
| Configure ICMP error message verification. You can either apply strict RST range checking or disable it. | |
| cli_audit_log string |
| Enable/disable CLI audit log. | |
| cloud_communication string |
| Enable/disable all cloud communication. | |
| clt_cert_req string |
| Enable/disable requiring administrators to have a client certificate to log into the GUI using HTTPS. | |
| compliance_check string |
| Enable/disable global PCI DSS compliance check. | |
| compliance_check_time string | Time of day to run scheduled PCI DSS compliance checks. | ||
| cpu_use_threshold integer | Threshold at which CPU usage is reported. (% of total CPU). | ||
| csr_ca_attribute string |
| Enable/disable the CA attribute in certificates. Some CA servers reject CSRs that have the CA attribute. | |
| daily_restart string |
| Enable/disable daily restart of FortiGate unit. Use the restart-time option to set the time of day for the restart. | |
| default_service_source_port string | Default service source port range. | ||
| device_identification_active_scan_delay integer | Number of seconds to passively scan a device before performing an active scan. (20 - 3600 sec, (20 sec to 1 hour)). | ||
| device_idle_timeout integer | Time in seconds that a device must be idle to automatically log the device user out. (30 - 31536000 sec (30 sec to 1 year)). | ||
| dh_params string |
| Number of bits to use in the Diffie-Hellman exchange for HTTPS/SSH protocols. | |
| dnsproxy_worker_count integer | DNS proxy worker count. | ||
| dst string |
| Enable/disable daylight saving time. | |
| edit_vdom_prompt string |
| Enable/disable edit new VDOM prompt. | |
| endpoint_control_fds_access string |
| Enable/disable access to the FortiGuard network for non-compliant endpoints. | |
| endpoint_control_portal_port integer | Endpoint control portal port (1 - 65535). | ||
| failtime integer | Fail-time for server lost. | ||
| faz_disk_buffer_size integer | Maximum disk buffer size to temporarily store logs destined for FortiAnalyzer. To be used in the event that FortiAnalyzer is unavailalble. | ||
| fds_statistics string |
| Enable/disable sending IPS, Application Control, and AntiVirus data to FortiGuard. This data is used to improve FortiGuard services and is not shared with external parties and is protected by Fortinet"s privacy policy. | |
| fds_statistics_period integer | FortiGuard statistics collection period in minutes. (1 - 1440 min (1 min to 24 hours)). | ||
| fec_port integer | Local UDP port for Forward Error Correction (49152 - 65535). | ||
| fgd_alert_subscription list / elements=string |
| Type of alert to retrieve from FortiGuard. | |
| fortiextender string |
| Enable/disable FortiExtender. | |
| fortiextender_data_port integer | FortiExtender data port (1024 - 49150). | ||
| fortiextender_vlan_mode string |
| Enable/disable FortiExtender VLAN mode. | |
| fortiipam_integration string |
| Enable/disable integration with the FortiIPAM cloud service. | |
| fortiservice_port integer | FortiService port (1 - 65535). Used by FortiClient endpoint compliance. Older versions of FortiClient used a different port. | ||
| fortitoken_cloud string |
| Enable/disable FortiToken Cloud service. | |
| gui_allow_default_hostname string |
| Enable/disable the GUI warning about using a default hostname | |
| gui_certificates string |
| Enable/disable the System > Certificate GUI page, allowing you to add and configure certificates from the GUI. | |
| gui_custom_language string |
| Enable/disable custom languages in GUI. | |
| gui_date_format string |
| Default date format used throughout GUI. | |
| gui_date_time_source string |
| Source from which the FortiGate GUI uses to display date and time entries. | |
| gui_device_latitude string | Add the latitude of the location of this FortiGate to position it on the Threat Map. | ||
| gui_device_longitude string | Add the longitude of the location of this FortiGate to position it on the Threat Map. | ||
| gui_display_hostname string |
| Enable/disable displaying the FortiGate"s hostname on the GUI login page. | |
| gui_firmware_upgrade_warning string |
| Enable/disable the firmware upgrade warning on the GUI. | |
| gui_forticare_registration_setup_warning string |
| Enable/disable the FortiCare registration setup warning on the GUI. | |
| gui_fortigate_cloud_sandbox string |
| Enable/disable displaying FortiGate Cloud Sandbox on the GUI. | |
| gui_fortisandbox_cloud string |
| Enable/disable displaying FortiSandbox Cloud on the GUI. | |
| gui_ipv6 string |
| Enable/disable IPv6 settings on the GUI. | |
| gui_lines_per_page integer | Number of lines to display per page for web administration. | ||
| gui_local_out string |
| Enable/disable Local-out traffic on the GUI. | |
| gui_replacement_message_groups string |
| Enable/disable replacement message groups on the GUI. | |
| gui_rest_api_cache string |
| Enable/disable REST API result caching on FortiGate. | |
| gui_theme string |
| Color scheme for the administration GUI. | |
| gui_wireless_opensecurity string |
| Enable/disable wireless open security option on the GUI. | |
| honor_df string |
| Enable/disable honoring of Don"t-Fragment (DF) flag. | |
| hostname string | FortiGate unit"s hostname. Most models will truncate names longer than 24 characters. Some models support hostnames up to 35 characters. | ||
| igmp_state_limit integer | Maximum number of IGMP memberships (96 - 64000). | ||
| interval integer | Dead gateway detection interval. | ||
| ip_src_port_range string | IP source port range used for traffic originating from the FortiGate unit. | ||
| ips_affinity string | Affinity setting for IPS (hexadecimal value up to 256 bits in the format of xxxxxxxxxxxxxxxx; allowed CPUs must be less than total number of IPS engine daemons). | ||
| ipsec_asic_offload string |
| Enable/disable ASIC offloading (hardware acceleration) for IPsec VPN traffic. Hardware acceleration can offload IPsec VPN sessions and accelerate encryption and decryption. | |
| ipsec_ha_seqjump_rate integer | ESP jump ahead rate (1G - 10G pps equivalent). | ||
| ipsec_hmac_offload string |
| Enable/disable offloading (hardware acceleration) of HMAC processing for IPsec VPN. | |
| ipsec_soft_dec_async string |
| Enable/disable software decryption asynchronization (using multiple CPUs to do decryption) for IPsec VPN traffic. | |
| ipv6_accept_dad integer | Enable/disable acceptance of IPv6 Duplicate Address Detection (DAD). | ||
| ipv6_allow_anycast_probe string |
| Enable/disable IPv6 address probe through Anycast. | |
| ipv6_allow_traffic_redirect string |
| Disable to prevent IPv6 traffic with same local ingress and egress interface from being forwarded without policy check. | |
| irq_time_accounting string |
| Configure CPU IRQ time accounting mode. | |
| language string |
| GUI display language. | |
| ldapconntimeout integer | Global timeout for connections with remote LDAP servers in milliseconds (1 - 300000). | ||
| lldp_reception string |
| Enable/disable Link Layer Discovery Protocol (LLDP) reception. | |
| lldp_transmission string |
| Enable/disable Link Layer Discovery Protocol (LLDP) transmission. | |
| log_ssl_connection string |
| Enable/disable logging of SSL connection events. | |
| log_uuid string |
| Whether UUIDs are added to traffic logs. You can disable UUIDs, add firewall policy UUIDs to traffic logs, or add all UUIDs to traffic logs. | |
| log_uuid_address string |
| Enable/disable insertion of address UUIDs to traffic logs. | |
| log_uuid_policy string |
| Enable/disable insertion of policy UUIDs to traffic logs. | |
| login_timestamp string |
| Enable/disable login time recording. | |
| long_vdom_name string |
| Enable/disable long VDOM name support. | |
| management_ip string | Management IP address of this FortiGate. Used to log into this FortiGate from another FortiGate in the Security Fabric. | ||
| management_port integer | Overriding port for management connection (Overrides admin port). | ||
| management_vdom string | Management virtual domain name. Source system.vdom.name. | ||
| max_dlpstat_memory integer | Maximum DLP stat memory (0 - 4294967295). | ||
| max_route_cache_size integer | Maximum number of IP route cache entries (0 - 2147483647). | ||
| mc_ttl_notchange string |
| Enable/disable no modification of multicast TTL. | |
| memory_use_threshold_extreme integer | Threshold at which memory usage is considered extreme (new sessions are dropped) (% of total RAM). | ||
| memory_use_threshold_green integer | Threshold at which memory usage forces the FortiGate to exit conserve mode (% of total RAM). | ||
| memory_use_threshold_red integer | Threshold at which memory usage forces the FortiGate to enter conserve mode (% of total RAM). | ||
| miglog_affinity string | Affinity setting for logging (64-bit hexadecimal value in the format of xxxxxxxxxxxxxxxx). | ||
| miglogd_children integer | Number of logging (miglogd) processes to be allowed to run. Higher number can reduce performance; lower number can slow log processing time. No logs will be dropped or lost if the number is changed. | ||
| multi_factor_authentication string |
| Enforce all login methods to require an additional authentication factor . | |
| multicast_forward string |
| Enable/disable multicast forwarding. | |
| ndp_max_entry integer | Maximum number of NDP table entries (set to 65,536 or higher; if set to 0, kernel holds 65,536 entries). | ||
| per_user_bal string |
| Enable/disable per-user block/allow list filter. | |
| per_user_bwl string |
| Enable/disable per-user black/white list filter. | |
| policy_auth_concurrent integer | Number of concurrent firewall use logins from the same user (1 - 100). | ||
| post_login_banner string |
| Enable/disable displaying the administrator access disclaimer message after an administrator successfully logs in. | |
| pre_login_banner string |
| Enable/disable displaying the administrator access disclaimer message on the login page before an administrator logs in. | |
| private_data_encryption string |
| Enable/disable private data encryption using an AES 128-bit key. | |
| proxy_auth_lifetime string |
| Enable/disable authenticated users lifetime control. This is a cap on the total time a proxy user can be authenticated for after which re-authentication will take place. | |
| proxy_auth_lifetime_timeout integer | Lifetime timeout in minutes for authenticated users (5 - 65535 min). | ||
| proxy_auth_timeout integer | Authentication timeout in minutes for authenticated users (1 - 300 min). | ||
| proxy_cipher_hardware_acceleration string |
| Enable/disable using content processor (CP8 or CP9) hardware acceleration to encrypt and decrypt IPsec and SSL traffic. | |
| proxy_hardware_acceleration string |
| Enable/disable email proxy hardware acceleration. | |
| proxy_kxp_hardware_acceleration string |
| Enable/disable using the content processor to accelerate KXP traffic. | |
| proxy_re_authentication_mode string |
| Control if users must re-authenticate after a session is closed, traffic has been idle, or from the point at which the user was first created. | |
| proxy_resource_mode string |
| Enable/disable use of the maximum memory usage on the FortiGate unit"s proxy processing of resources, such as block lists, allow lists, and external resources. | |
| proxy_worker_count integer | Proxy worker count. | ||
| radius_port integer | RADIUS service port number. | ||
| reboot_upon_config_restore string |
| Enable/disable reboot of system upon restoring configuration. | |
| refresh integer | Statistics refresh interval in GUI. | ||
| remoteauthtimeout integer | Number of seconds that the FortiGate waits for responses from remote RADIUS, LDAP, or TACACS+ authentication servers. (0-300 sec). | ||
| reset_sessionless_tcp string |
| Action to perform if the FortiGate receives a TCP packet but cannot find a corresponding session in its session table. NAT/Route mode only. | |
| restart_time string | Daily restart time (hh:mm). | ||
| revision_backup_on_logout string |
| Enable/disable back-up of the latest configuration revision when an administrator logs out of the CLI or GUI. | |
| revision_image_auto_backup string |
| Enable/disable back-up of the latest configuration revision after the firmware is upgraded. | |
| scanunit_count integer | Number of scanunits. The range and the default depend on the number of CPUs. Only available on FortiGate units with multiple CPUs. | ||
| security_rating_result_submission string |
| Enable/disable the submission of Security Rating results to FortiGuard. | |
| security_rating_run_on_schedule string |
| Enable/disable scheduled runs of Security Rating. | |
| send_pmtu_icmp string |
| Enable/disable sending of path maximum transmission unit (PMTU) - ICMP destination unreachable packet and to support PMTUD protocol on your network to reduce fragmentation of packets. | |
| snat_route_change string |
| Enable/disable the ability to change the static NAT route. | |
| special_file_23_support string |
| Enable/disable IPS detection of HIBUN format files when using Data Leak Protection. | |
| split_port string | Split port(s) to multiple 10Gbps ports. | ||
| ssd_trim_date integer | Date within a month to run ssd trim. | ||
| ssd_trim_freq string |
| How often to run SSD Trim . SSD Trim prevents SSD drive data loss by finding and isolating errors. | |
| ssd_trim_hour integer | Hour of the day on which to run SSD Trim (0 - 23). | ||
| ssd_trim_min integer | Minute of the hour on which to run SSD Trim (0 - 59, 60 for random). | ||
| ssd_trim_weekday string |
| Day of week to run SSD Trim. | |
| ssh_cbc_cipher string |
| Enable/disable CBC cipher for SSH access. | |
| ssh_hmac_md5 string |
| Enable/disable HMAC-MD5 for SSH access. | |
| ssh_kex_sha1 string |
| Enable/disable SHA1 key exchange for SSH access. | |
| ssh_mac_weak string |
| Enable/disable HMAC-SHA1 and UMAC-64-ETM for SSH access. | |
| ssl_min_proto_version string |
| Minimum supported protocol version for SSL/TLS connections . | |
| ssl_static_key_ciphers string |
| Enable/disable static key ciphers in SSL/TLS connections (e.g. AES128-SHA, AES256-SHA, AES128-SHA256, AES256-SHA256). | |
| sslvpn_cipher_hardware_acceleration string |
| Enable/disable SSL VPN hardware acceleration. | |
| sslvpn_ems_sn_check string |
| Enable/disable verification of EMS serial number in SSL-VPN connection. | |
| sslvpn_kxp_hardware_acceleration string |
| Enable/disable SSL VPN KXP hardware acceleration. | |
| sslvpn_max_worker_count integer | Maximum number of SSL VPN processes. Upper limit for this value is the number of CPUs and depends on the model. | ||
| sslvpn_plugin_version_check string |
| Enable/disable checking browser"s plugin version by SSL VPN. | |
| strict_dirty_session_check string |
| Enable to check the session against the original policy when revalidating. This can prevent dropping of redirected sessions when web-filtering and authentication are enabled together. If this option is enabled, the FortiGate unit deletes a session if a routing or policy change causes the session to no longer match the policy that originally allowed the session. | |
| strong_crypto string |
| Enable to use strong encryption and only allow strong ciphers (AES, 3DES) and digest (SHA1) for HTTPS/SSH/TLS/SSL functions. | |
| switch_controller string |
| Enable/disable switch controller feature. Switch controller allows you to manage FortiSwitch from the FortiGate itself. | |
| switch_controller_reserved_network string | Enable reserved network subnet for controlled switches. This is available when the switch controller is enabled. | ||
| sys_perf_log_interval integer | Time in minutes between updates of performance statistics logging. (1 - 15 min). | ||
| tcp_halfclose_timer integer | Number of seconds the FortiGate unit should wait to close a session after one peer has sent a FIN packet but the other has not responded (1 - 86400 sec (1 day)). | ||
| tcp_halfopen_timer integer | Number of seconds the FortiGate unit should wait to close a session after one peer has sent an open session packet but the other has not responded (1 - 86400 sec (1 day)). | ||
| tcp_option string |
| Enable SACK, timestamp and MSS TCP options. | |
| tcp_rst_timer integer | Length of the TCP CLOSE state in seconds (5 - 300 sec). | ||
| tcp_timewait_timer integer | Length of the TCP TIME-WAIT state in seconds. | ||
| tftp string |
| Enable/disable TFTP. | |
| timezone string |
| Number corresponding to your time zone from 00 to 86. Enter set timezone ? to view the list of time zones and the numbers that represent them. | |
| tp_mc_skip_policy string |
| Enable/disable skip policy check and allow multicast through. | |
| traffic_priority string |
| Choose Type of Service (ToS) or Differentiated Services Code Point (DSCP) for traffic prioritization in traffic shaping. | |
| traffic_priority_level string |
| Default system-wide level of priority for traffic prioritization. | |
| two_factor_email_expiry integer | Email-based two-factor authentication session timeout (30 - 300 seconds (5 minutes)). | ||
| two_factor_fac_expiry integer | FortiAuthenticator token authentication session timeout (10 - 3600 seconds (1 hour)). | ||
| two_factor_ftk_expiry integer | FortiToken authentication session timeout (60 - 600 sec (10 minutes)). | ||
| two_factor_ftm_expiry integer | FortiToken Mobile session timeout (1 - 168 hours (7 days)). | ||
| two_factor_sms_expiry integer | SMS-based two-factor authentication session timeout (30 - 300 sec). | ||
| udp_idle_timer integer | UDP connection session timeout. This command can be useful in managing CPU and memory resources (1 - 86400 seconds (1 day)). | ||
| url_filter_affinity string | URL filter CPU affinity. | ||
| url_filter_count integer | URL filter daemon count. | ||
| user_device_store_max_devices integer | Maximum number of devices allowed in user device store. | ||
| user_device_store_max_users integer | Maximum number of users allowed in user device store. | ||
| user_server_cert string | Certificate to use for https user authentication. Source certificate.local.name. | ||
| vdom_admin string |
| Enable/disable support for multiple virtual domains (VDOMs). | |
| vdom_mode string |
| Enable/disable support for split/multiple virtual domains (VDOMs). | |
| vip_arp_range string |
| Controls the number of ARPs that the FortiGate sends for a Virtual IP (VIP) address range. | |
| virtual_server_count integer | Maximum number of virtual server processes to create. The maximum is the number of CPU cores. This is not available on single-core CPUs. | ||
| virtual_server_hardware_acceleration string |
| Enable/disable virtual server hardware acceleration. | |
| wad_affinity string | Affinity setting for wad (hexadecimal value up to 256 bits in the format of xxxxxxxxxxxxxxxx). | ||
| wad_csvc_cs_count integer | Number of concurrent WAD-cache-service object-cache processes. | ||
| wad_csvc_db_count integer | Number of concurrent WAD-cache-service byte-cache processes. | ||
| wad_memory_change_granularity integer | Minimum percentage change in system memory usage detected by the wad daemon prior to adjusting TCP window size for any active connection. | ||
| wad_source_affinity string |
| Enable/disable dispatching traffic to WAD workers based on source affinity. | |
| wad_worker_count integer | Number of explicit proxy WAN optimization daemon (WAD) processes. By default WAN optimization, explicit proxy, and web caching is handled by all of the CPU cores in a FortiGate unit. | ||
| wifi_ca_certificate string | CA certificate that verifies the WiFi certificate. Source certificate.ca.name. | ||
| wifi_certificate string | Certificate to use for WiFi authentication. Source certificate.local.name. | ||
| wimax_4g_usb string |
| Enable/disable comparability with WiMAX 4G USB devices. | |
| wireless_controller string |
| Enable/disable the wireless controller feature to use the FortiGate unit to manage FortiAPs. | |
| wireless_controller_port integer | Port used for the control channel in wireless controller mode (wireless-mode is ac). The data channel port is the control channel port number plus one (1024 - 49150). | ||
| vdom string | Default: "root" | Virtual domain, among those defined previously. A vdom is a virtual instance of the FortiGate that can be configured and used as a different unit. | |
Note
- hosts: fortigates
collections:
- fortinet.fortios
connection: httpapi
vars:
vdom: "root"
ansible_httpapi_use_ssl: yes
ansible_httpapi_validate_certs: no
ansible_httpapi_port: 443
tasks:
- name: Configure global attributes.
fortios_system_global:
vdom: "{{ vdom }}"
system_global:
admin_concurrent: "enable"
admin_console_timeout: "4"
admin_forticloud_sso_login: "enable"
admin_hsts_max_age: "6"
admin_https_pki_required: "enable"
admin_https_redirect: "enable"
admin_https_ssl_versions: "tlsv1-0"
admin_lockout_duration: "10"
admin_lockout_threshold: "11"
admin_login_max: "12"
admin_maintainer: "enable"
admin_port: "14"
admin_restrict_local: "enable"
admin_scp: "enable"
admin_server_cert: "<your_own_value> (source certificate.local.name)"
admin_sport: "18"
admin_ssh_grace_time: "19"
admin_ssh_password: "enable"
admin_ssh_port: "21"
admin_ssh_v1: "enable"
admin_telnet: "enable"
admin_telnet_port: "24"
admintimeout: "25"
alias: "<your_own_value>"
allow_traffic_redirect: "enable"
anti_replay: "disable"
arp_max_entry: "29"
asymroute: "enable"
auth_cert: "<your_own_value> (source certificate.local.name)"
auth_http_port: "32"
auth_https_port: "33"
auth_keepalive: "enable"
auth_session_limit: "block-new"
auto_auth_extension_device: "enable"
autorun_log_fsck: "enable"
av_affinity: "<your_own_value>"
av_failopen: "pass"
av_failopen_session: "enable"
batch_cmdb: "enable"
block_session_timer: "42"
br_fdb_max_entry: "43"
cert_chain_max: "44"
cfg_revert_timeout: "45"
cfg_save: "automatic"
check_protocol_header: "loose"
check_reset_range: "strict"
cli_audit_log: "enable"
cloud_communication: "enable"
clt_cert_req: "enable"
compliance_check: "enable"
compliance_check_time: "<your_own_value>"
cpu_use_threshold: "54"
csr_ca_attribute: "enable"
daily_restart: "enable"
default_service_source_port: "<your_own_value>"
device_identification_active_scan_delay: "58"
device_idle_timeout: "59"
dh_params: "1024"
dnsproxy_worker_count: "61"
dst: "enable"
edit_vdom_prompt: "enable"
endpoint_control_fds_access: "enable"
endpoint_control_portal_port: "65"
failtime: "66"
faz_disk_buffer_size: "67"
fds_statistics: "enable"
fds_statistics_period: "69"
fec_port: "70"
fgd_alert_subscription: "advisory"
fortiextender: "enable"
fortiextender_data_port: "73"
fortiextender_vlan_mode: "enable"
fortiipam_integration: "enable"
fortiservice_port: "76"
fortitoken_cloud: "enable"
gui_allow_default_hostname: "enable"
gui_certificates: "enable"
gui_custom_language: "enable"
gui_date_format: "yyyy/MM/dd"
gui_date_time_source: "system"
gui_device_latitude: "<your_own_value>"
gui_device_longitude: "<your_own_value>"
gui_display_hostname: "enable"
gui_firmware_upgrade_warning: "enable"
gui_forticare_registration_setup_warning: "enable"
gui_fortigate_cloud_sandbox: "enable"
gui_fortisandbox_cloud: "enable"
gui_ipv6: "enable"
gui_lines_per_page: "91"
gui_local_out: "enable"
gui_replacement_message_groups: "enable"
gui_rest_api_cache: "enable"
gui_theme: "green"
gui_wireless_opensecurity: "enable"
honor_df: "enable"
hostname: "myhostname"
igmp_state_limit: "99"
interval: "100"
ip_src_port_range: "<your_own_value>"
ips_affinity: "<your_own_value>"
ipsec_asic_offload: "enable"
ipsec_ha_seqjump_rate: "104"
ipsec_hmac_offload: "enable"
ipsec_soft_dec_async: "enable"
ipv6_accept_dad: "107"
ipv6_allow_anycast_probe: "enable"
ipv6_allow_traffic_redirect: "enable"
irq_time_accounting: "auto"
language: "english"
ldapconntimeout: "112"
lldp_reception: "enable"
lldp_transmission: "enable"
log_ssl_connection: "enable"
log_uuid: "disable"
log_uuid_address: "enable"
log_uuid_policy: "enable"
login_timestamp: "enable"
long_vdom_name: "enable"
management_ip: "<your_own_value>"
management_port: "122"
management_vdom: "<your_own_value> (source system.vdom.name)"
max_dlpstat_memory: "124"
max_route_cache_size: "125"
mc_ttl_notchange: "enable"
memory_use_threshold_extreme: "127"
memory_use_threshold_green: "128"
memory_use_threshold_red: "129"
miglog_affinity: "<your_own_value>"
miglogd_children: "131"
multi_factor_authentication: "optional"
multicast_forward: "enable"
ndp_max_entry: "134"
per_user_bal: "enable"
per_user_bwl: "enable"
policy_auth_concurrent: "137"
post_login_banner: "disable"
pre_login_banner: "enable"
private_data_encryption: "disable"
proxy_auth_lifetime: "enable"
proxy_auth_lifetime_timeout: "142"
proxy_auth_timeout: "143"
proxy_cipher_hardware_acceleration: "disable"
proxy_hardware_acceleration: "disable"
proxy_kxp_hardware_acceleration: "disable"
proxy_re_authentication_mode: "session"
proxy_resource_mode: "enable"
proxy_worker_count: "149"
radius_port: "150"
reboot_upon_config_restore: "enable"
refresh: "152"
remoteauthtimeout: "153"
reset_sessionless_tcp: "enable"
restart_time: "<your_own_value>"
revision_backup_on_logout: "enable"
revision_image_auto_backup: "enable"
scanunit_count: "158"
security_rating_result_submission: "enable"
security_rating_run_on_schedule: "enable"
send_pmtu_icmp: "enable"
snat_route_change: "enable"
special_file_23_support: "disable"
split_port: "<your_own_value>"
ssd_trim_date: "165"
ssd_trim_freq: "never"
ssd_trim_hour: "167"
ssd_trim_min: "168"
ssd_trim_weekday: "sunday"
ssh_cbc_cipher: "enable"
ssh_hmac_md5: "enable"
ssh_kex_sha1: "enable"
ssh_mac_weak: "enable"
ssl_min_proto_version: "SSLv3"
ssl_static_key_ciphers: "enable"
sslvpn_cipher_hardware_acceleration: "enable"
sslvpn_ems_sn_check: "enable"
sslvpn_kxp_hardware_acceleration: "enable"
sslvpn_max_worker_count: "179"
sslvpn_plugin_version_check: "enable"
strict_dirty_session_check: "enable"
strong_crypto: "enable"
switch_controller: "disable"
switch_controller_reserved_network: "<your_own_value>"
sys_perf_log_interval: "185"
tcp_halfclose_timer: "186"
tcp_halfopen_timer: "187"
tcp_option: "enable"
tcp_rst_timer: "189"
tcp_timewait_timer: "190"
tftp: "enable"
timezone: "01"
tp_mc_skip_policy: "enable"
traffic_priority: "tos"
traffic_priority_level: "low"
two_factor_email_expiry: "196"
two_factor_fac_expiry: "197"
two_factor_ftk_expiry: "198"
two_factor_ftm_expiry: "199"
two_factor_sms_expiry: "200"
udp_idle_timer: "201"
url_filter_affinity: "<your_own_value>"
url_filter_count: "203"
user_device_store_max_devices: "204"
user_device_store_max_users: "205"
user_server_cert: "<your_own_value> (source certificate.local.name)"
vdom_admin: "enable"
vdom_mode: "no-vdom"
vip_arp_range: "unlimited"
virtual_server_count: "210"
virtual_server_hardware_acceleration: "disable"
wad_affinity: "<your_own_value>"
wad_csvc_cs_count: "213"
wad_csvc_db_count: "214"
wad_memory_change_granularity: "215"
wad_source_affinity: "disable"
wad_worker_count: "217"
wifi_ca_certificate: "<your_own_value> (source certificate.ca.name)"
wifi_certificate: "<your_own_value> (source certificate.local.name)"
wimax_4g_usb: "enable"
wireless_controller: "enable"
wireless_controller_port: "222"
Common return values are documented here, the following are the fields unique to this module:
| Key | Returned | Description |
|---|---|---|
| build string | always | Build number of the fortigate image Sample: 1547 |
| http_method string | always | Last method used to provision the content into FortiGate Sample: PUT |
| http_status string | always | Last result given by FortiGate on last operation applied Sample: 200 |
| mkey string | success | Master key (id) used in the last call to FortiGate Sample: id |
| name string | always | Name of the table used to fulfill the request Sample: urlfilter |
| path string | always | Path of the table used to fulfill the request Sample: webfilter |
| revision string | always | Internal revision number Sample: 17.0.2.10658 |
| serial string | always | Serial number of the unit Sample: FGVMEVYYQT3AB5352 |
| status string | always | Indication of the operation's result Sample: success |
| vdom string | always | Virtual domain used Sample: root |
| version string | always | Version of the FortiGate Sample: v5.6.3 |
© 2012–2018 Michael DeHaan
© 2018–2021 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/latest/collections/fortinet/fortios/fortios_system_global_module.html