W3cubDocs

/Ansible 2.10

community.network.flowadm – Manage bandwidth resource control and priority for protocols, services and zones on Solaris/illumos systems

Note

This plugin is part of the community.network collection.

To install it use: ansible-galaxy collection install community.network.

To use it in a playbook, specify: community.network.flowadm.

Synopsis

  • Create/modify/remove networking bandwidth and associated resources for a type of traffic on a particular link.

Parameters

Parameter Choices/Defaults Comments
dsfield
string
- Identifies the 8-bit differentiated services field (as defined in RFC 2474). The optional dsfield_mask is used to state the bits of interest in the differentiated services field when comparing with the dsfield value. Both values must be in hexadecimal.
link
string
Specifiies a link to configure flow on.
local_ip
string
Identifies a network flow by the local IP address.
local_port
string
Identifies a service specified by the local port.
maxbw
string
- Sets the full duplex bandwidth for the flow. The bandwidth is specified as an integer with one of the scale suffixes(K, M, or G for Kbps, Mbps, and Gbps). If no units are specified, the input value will be read as Mbps.
name
string / required
- A flow is defined as a set of attributes based on Layer 3 and Layer 4 headers, which can be used to identify a protocol, service, or a zone.

aliases: flow
priority
string
    Choices:
  • low
  • medium ←
  • high
Sets the relative priority for the flow.
remote_ip
string
Identifies a network flow by the remote IP address.
state
string
    Choices:
  • absent
  • present ←
  • resetted
Create/delete/enable/disable an IP address on the network interface.
temporary
boolean
    Choices:
  • no ←
  • yes
Specifies that the configured flow is temporary. Temporary flows do not persist across reboots.
transport
string
- Specifies a Layer 4 protocol to be used. It is typically used in combination with local_port to identify the service that needs special attention.

Examples

- name: Limit SSH traffic to 100M via vnic0 interface
  community.network.flowadm:
    link: vnic0
    flow: ssh_out
    transport: tcp
    local_port: 22
    maxbw: 100M
    state: present

- name: Reset flow properties
  community.network.flowadm:
    name: dns
    state: resetted

- name: Configure policy for EF PHB (DSCP value of 101110 from RFC 2598) with a bandwidth of 500 Mbps and a high priority
  community.network.flowadm:
    link: bge0
    dsfield: '0x2e:0xfc'
    maxbw: 500M
    priority: high
    flow: efphb-flow
    state: present

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
dsfield
string
if dsfield is defined
flow's differentiated services value

Sample:
0x2e:0xfc
link
string
if link is defined
flow's link

Sample:
vnic0
local_Ip
string
if local_ip is defined
flow's local IP address

Sample:
10.0.0.42
local_port
integer
if local_port is defined
flow's local port

Sample:
1337
maxbw
string
if maxbw is defined
flow's maximum bandwidth

Sample:
100M
name
string
always
flow name

Sample:
http_drop
priority
string
if priority is defined
flow's priority

Sample:
low
remote_Ip
string
if remote_ip is defined
flow's remote IP address

Sample:
10.0.0.42
state
string
always
state of the target

Sample:
present
temporary
boolean
always
flow's persistence

Sample:
True
transport
string
if transport is defined
flow's transport

Sample:
tcp


Authors

  • Adam Števko (@xen0l)

© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.10/collections/community/network/flowadm_module.html