W3cubDocs

/Ansible 2.11

cisco.iosxr.iosxr_acls – ACLs resource module

Note

This plugin is part of the cisco.iosxr collection (version 1.2.1).

To install it use: ansible-galaxy collection install cisco.iosxr.

To use it in a playbook, specify: cisco.iosxr.iosxr_acls.

New in version 1.0.0: of cisco.iosxr

Synopsis
Parameters
Examples
Return Values

Synopsis

This module manages Access Control Lists (ACLs) on devices running IOS-XR.

Note

This module has a corresponding action plugin.

Parameters

Parameter							Choices/Defaults	Comments
config list / elements=dictionary								A list of dictionaries specifying ACL configurations.
	acls list / elements=dictionary							A list of Access Control Lists (ACLs).
		aces list / elements=dictionary						List of Access Control Entries (ACEs) for this Access Control List (ACL).
			authen boolean				Choices: no yes	Match if authentication header is present.
			capture boolean				Choices: no yes	Capture matched packet.
			destination dictionary					Specifies the packet destination.
				address string				The destination IP address to match.
				any boolean			Choices: no yes	Match any destination address.
				host string				The host IP address to match.
				port_protocol dictionary				Specify the source port or protocol.
					eq string			Match only packets on a given port number.
					gt string			Match only packets with a greater port number.
					lt string			Match only packets with a lower port number.
					neq string			Match only packets not on a given port number.
					range dictionary			Match only packets in the range of port numbers
						end string		Specify the end of the port range
						start string		Specify the start of the port range
				prefix string				Destination network prefix.
				wildcard_bits string				The Wildcard bits to apply to destination address.
			destopts boolean				Choices: no yes	Match if destination opts header is present.
			dscp dictionary					Match packets with given DSCP value.
				eq string				Match only packets on a given dscp value
				gt string				Match only packets with a greater dscp value
				lt string				Match only packets with a lower dscp value
				neq string				Match only packets not on a given dscp value
				range dictionary				Match only packets in the range of dscp values
					end string			End of the dscp range
					start string			Start of the dscp range
			fragments boolean				Choices: no yes	Check non-intial fragments.
			grant string				Choices: permit deny	Forward or drop packets matching the Access Control Entry (ACE).
			hop_by_hop boolean				Choices: no yes	Match if hop-by-hop opts header is present.
			icmp_off boolean				Choices: no yes	Enable/disable the ICMP message for this entry.
			line string					An ACE excluding the sequence number. This key is mutually exclusive with all the other attributes except 'sequence'. When used with other attributes, the value of this key will get precedence and the other keys will be ignored. This should only be used when an attribute doesn't exist in the argspec but is valid for the device. For fact gathering, any ACE that is not fully parsed, will show up as a value of this attribute, excluding the sequence number, which will be populated as value of the sequence key. aliases: ace
			log boolean				Choices: no yes	Enable/disable log matches against this entry.
			log_input boolean				Choices: no yes	Enable/disable log matches against this entry, including input interface.
			packet_length dictionary					Match packets given packet length.
				eq integer				Match only packets on a given packet length
				gt integer				Match only packets with a greater packet length
				lt integer				Match only packets with a lower packet length
				neq integer				Match only packets not on a given packet length
				range dictionary				Match only packets in the range of packet lengths
					end integer			End of the packet length range
					start integer			Start of the packet length range
			precedence string					Match packets with given precedence value
			protocol string					Specify the protocol to match. Refer to vendor documentation for valid values.
			protocol_options dictionary					Additional suboptions for the protocol.
				icmp dictionary				Internet Control Message Protocol settings.
					administratively_prohibited boolean		Choices: no yes	Administratively prohibited
					alternate_address boolean		Choices: no yes	Alternate address
					conversion_error boolean		Choices: no yes	Datagram conversion
					dod_host_prohibited boolean		Choices: no yes	Host prohibited
					dod_net_prohibited boolean		Choices: no yes	Net prohibited
					echo boolean		Choices: no yes	Echo (ping)
					echo_reply boolean		Choices: no yes	Echo reply
					general_parameter_problem boolean		Choices: no yes	Parameter problem
					host_isolated boolean		Choices: no yes	Host isolated
					host_precedence_unreachable boolean		Choices: no yes	Host unreachable for precedence
					host_redirect boolean		Choices: no yes	Host redirect
					host_tos_redirect boolean		Choices: no yes	Host redirect for TOS
					host_tos_unreachable boolean		Choices: no yes	Host unreachable for TOS
					host_unknown boolean		Choices: no yes	Host unknown
					host_unreachable boolean		Choices: no yes	Host unreachable
					information_reply boolean		Choices: no yes	Information replies
					information_request boolean		Choices: no yes	Information requests
					mask_reply boolean		Choices: no yes	Mask replies
					mask_request boolean		Choices: no yes	Mask requests
					mobile_redirect boolean		Choices: no yes	Mobile host redirect
					net_redirect boolean		Choices: no yes	Network redirect
					net_tos_redirect boolean		Choices: no yes	Net redirect for TOS
					net_tos_unreachable boolean		Choices: no yes	Network unreachable for TOS
					net_unreachable boolean		Choices: no yes	Net unreachable
					network_unknown boolean		Choices: no yes	Network unknown
					no_room_for_option boolean		Choices: no yes	Parameter required but no room
					option_missing boolean		Choices: no yes	Parameter required but not present
					packet_too_big boolean		Choices: no yes	Fragmentation needed and DF set
					parameter_problem boolean		Choices: no yes	All parameter problems
					port_unreachable boolean		Choices: no yes	Port unreachable
					precedence_unreachable boolean		Choices: no yes	Precedence cutoff
					protocol_unreachable boolean		Choices: no yes	Protocol unreachable
					reassembly_timeout boolean		Choices: no yes	Reassembly timeout
					redirect boolean		Choices: no yes	All redirects
					router_advertisement boolean		Choices: no yes	Router discovery advertisements
					router_solicitation boolean		Choices: no yes	Router discovery solicitations
					source_quench boolean		Choices: no yes	Source quenches
					source_route_failed boolean		Choices: no yes	Source route failed
					time_exceeded boolean		Choices: no yes	All time exceededs
					timestamp_reply boolean		Choices: no yes	Timestamp replies
					timestamp_request boolean		Choices: no yes	Timestamp requests
					traceroute boolean		Choices: no yes	Traceroute
					ttl_exceeded boolean		Choices: no yes	TTL exceeded
					unreachable boolean		Choices: no yes	All unreachables
				icmpv6 dictionary				Internet Control Message Protocol settings for IPv6.
					address_unreachable boolean		Choices: no yes	Address Unreachable
					administratively_prohibited boolean		Choices: no yes	Administratively Prohibited
					beyond_scope_of_source_address boolean		Choices: no yes	Administratively Prohibited
					destination_unreachable boolean		Choices: no yes	Destination Unreachable
					echo boolean		Choices: no yes	Echo
					echo_reply boolean		Choices: no yes	Echo Reply
					erroneous_header_field boolean		Choices: no yes	Erroneous Header Field
					group_membership_query boolean		Choices: no yes	Group Membership Query
					group_membership_report boolean		Choices: no yes	Group Membership Report
					group_membership_termination boolean		Choices: no yes	Group Membership Termination
					host_unreachable boolean		Choices: no yes	Host Unreachable
					nd_na boolean		Choices: no yes	Neighbor Discovery - Neighbor Advertisement
					nd_ns boolean		Choices: no yes	Neighbor Discovery - Neighbor Solicitation
					neighbor_redirect boolean		Choices: no yes	Neighbor Redirect
					no_route_to_destination boolean		Choices: no yes	No Route To Destination
					node_information_request_is_refused boolean		Choices: no yes	Node Information Request Is Refused
					node_information_successful_reply boolean		Choices: no yes	Node Information Successful Reply
					packet_too_big boolean		Choices: no yes	Packet Too Big
					parameter_problem boolean		Choices: no yes	Parameter Problem
					port_unreachable boolean		Choices: no yes	Port Unreachable
					query_subject_is_domainname boolean		Choices: no yes	Query Subject Is Domain name
					query_subject_is_IPv4address boolean		Choices: no yes	Query Subject Is IPv4 address
					query_subject_is_IPv6address boolean		Choices: no yes	Query Subject Is IPv6 address
					reassembly_timeout boolean		Choices: no yes	Reassembly Timeout
					redirect boolean		Choices: no yes	Redirect
					router_advertisement boolean		Choices: no yes	Router Advertisement
					router_renumbering boolean		Choices: no yes	Router Renumbering
					router_solicitation boolean		Choices: no yes	Router Solicitation
					rr_command boolean		Choices: no yes	RR Command
					rr_result boolean		Choices: no yes	RR Result
					rr_seqnum_reset boolean		Choices: no yes	RR Seqnum Reset
					time_exceeded boolean		Choices: no yes	Time Exceeded
					ttl_exceeded boolean		Choices: no yes	TTL Exceeded
					unknown_query_type boolean		Choices: no yes	Unknown Query Type
					unreachable boolean		Choices: no yes	Unreachable
					unrecognized_next_header boolean		Choices: no yes	Unrecognized Next Header
					unrecognized_option boolean		Choices: no yes	Unrecognized Option
					whoareyou_reply boolean		Choices: no yes	Whoareyou Reply
					whoareyou_request boolean		Choices: no yes	Whoareyou Request
				igmp dictionary				Internet Group Management Protocol (IGMP) settings.
					dvmrp boolean		Choices: no yes	Match Distance Vector Multicast Routing Protocol
					host_query boolean		Choices: no yes	Match Host Query
					host_report boolean		Choices: no yes	Match Host Report
					mtrace boolean		Choices: no yes	Match mtrace
					mtrace_response boolean		Choices: no yes	Match mtrace response
					pim boolean		Choices: no yes	Match Protocol Independent Multicast
					trace boolean		Choices: no yes	Multicast trace
				tcp dictionary				Match TCP packet flags
					ack boolean		Choices: no yes	Match on the ACK bit
					established boolean		Choices: no yes	Match established connections
					fin boolean		Choices: no yes	Match on the FIN bit
					psh boolean		Choices: no yes	Match on the PSH bit
					rst boolean		Choices: no yes	Match on the RST bit
					syn boolean		Choices: no yes	Match on the SYN bit
					urg boolean		Choices: no yes	Match on the URG bit
			remark string					Comments or a description for the access list.
			routing boolean				Choices: no yes	Match if routing header is present.
			sequence integer					Sequence number for the Access Control Entry (ACE).
			source dictionary					Specifies the packet source.
				address string				The source IP address to match.
				any boolean			Choices: no yes	Match any source address.
				host string				The host IP address to match.
				port_protocol dictionary				Specify the source port or protocol.
					eq string			Match only packets on a given port number.
					gt string			Match only packets with a greater port number.
					lt string			Match only packets with a lower port number.
					neq string			Match only packets not on a given port number.
					range dictionary			Match only packets in the range of port numbers
						end string		Specify the end of the port range
						start string		Specify the start of the port range
				prefix string				Source network prefix.
				wildcard_bits string				The Wildcard bits to apply to source address.
			ttl dictionary					Match against specified TTL value.
				eq integer				Match only packets with exact TTL value.
				gt integer				Match only packets with a greater TTL value.
				lt integer				Match only packets with a lower TTL value.
				neq integer				Match only packets that won't have the given TTL value.
				range dictionary				Match only packets in the range of given TTL values.
					end integer			End of the TTL range.
					start integer			Start of the TTL range.
		name string						The name of the Access Control List (ACL).
	afi string / required						Choices: ipv4 ipv6	The Address Family Indicator (AFI) for the Access Control Lists (ACL).
running_config string								The module, by default, will connect to the remote device and retrieve the current running-config to use as a base for comparing against the contents of source. There are times when it is not desirable to have the task get the current running-config for every task in a playbook. The running_config argument allows the implementer to pass in the configuration to use as the base config for comparison. This value of this option should be the output received from device by executing command show running-config router static.
state string							Choices: merged ← replaced overridden deleted gathered rendered parsed	The state the configuration should be left in.

Examples

# Using merged to add new ACLs

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:07:45.767 UTC
# RP/0/RP0/CPU0:ios#

- name: Merge the provided configuration with the exisiting running configuration
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv6
      acls:
      - name: acl6_1
        aces:
        - sequence: 10
          grant: deny
          protocol: tcp
          source:
            prefix: 2001:db8:1234::/48
            port_protocol:
              range:
                start: ftp
                end: telnet
          destination:
            any: true
          protocol_options:
            tcp:
              syn: true
          ttl:
            range:
              start: 180
              end: 250
          routing: true
          authen: true
          log: true

        - sequence: 20
          grant: permit
          protocol: icmpv6
          source:
            any: true
          destination:
            any: true
          protocol_options:
            icmpv6:
              router_advertisement: true
          precedence: network
          destopts: true

    - afi: ipv4
      acls:
      - name: acl_1
        aces:
        - sequence: 16
          remark: TEST_ACL_1_REMARK

        - sequence: 21
          grant: permit
          protocol: tcp
          source:
            host: 192.0.2.10
            port_protocol:
              range:
                start: pop3
                end: 121
          destination:
            address: 198.51.100.0
            wildcard_bits: 0.0.0.15
          protocol_options:
            tcp:
              rst: true

        - sequence: 23
          grant: deny
          protocol: icmp
          source:
            any: true
          destination:
            prefix: 198.51.100.0/28
          protocol_options:
            icmp:
              reassembly_timeout: true
          dscp:
            lt: af12

      - name: acl_2
        aces:
        - sequence: 10
          remark: TEST_ACL_2_REMARK
    state: merged

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

# Using merged to update existing ACLs

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

- name: Update existing ACEs
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv4
      acls:
      - name: acl_1
        aces:
        - sequence: 21
          source:
            prefix: 198.51.100.32/28
            port_protocol:
              range:
                start: pop3
                end: 121
          protocol_options:
            tcp:
              syn: true

        - sequence: 23
          protocol_options:
            icmp:
              router_advertisement: true
          dscp:
            eq: af23

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:47:18.711 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp 198.51.100.32 0.0.0.15 range pop3 121 198.51.100.0 0.0.0.15 syn
#  23 deny icmp any 198.51.100.0 0.0.0.15 router-advertisement dscp eq af23
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

# Using replaced to replace a whole ACL

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

- name: Replace device configurations of listed ACL with provided configurations
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv4
      acls:
      - name: acl_2
        aces:
        - sequence: 11
          grant: permit
          protocol: igmp
          source:
            host: 198.51.100.130
          destination:
            any: true
          ttl:
            eq: 100

        - sequence: 12
          grant: deny
          source:
            any: true
          destination:
            any: true
          protocol: icmp
    state: replaced

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 06:19:51.496 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp 198.51.100.32 0.0.0.15 range pop3 121 198.51.100.0 0.0.0.15 syn
#  23 deny icmp any 198.51.100.0 0.0.0.15 router-advertisement dscp eq af23
# ipv4 access-list acl_2
#  11 permit igmp host 198.51.100.130 any ttl eq 100
#  12 deny icmp any any
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

# Using overridden to override all ACLs in the device

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

- name: Overridde all ACLs configuration with provided configuration
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv4
      acls:
      - name: acl_1
        aces:
        - sequence: 10
          grant: permit
          source:
            any: true
          destination:
            any: true
          protocol: tcp

      - name: acl_2
        aces:
        - sequence: 20
          grant: permit
          source:
            any: true
          destination:
            any: true
          protocol: igmp
    state: overridden

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 06:31:22.178 UTC
# ipv4 access-list acl_1
#  10 permit tcp any any
# ipv4 access-list acl_2
#  20 permit igmp any any

# Using deleted to delete an entire ACL

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

- name: Delete a single ACL
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv6
      acls:
      - name: acl6_1
    state: deleted

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK

# Using deleted to delete all ACLs under one AFI

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

- name: Delete all ACLs under one AFI
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv4
    state: deleted

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

# Using deleted to delete all ACLs from the device

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

- name: Delete all ACLs from the device
  cisco.iosxr.iosxr_acls:
    state: deleted

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:07:45.767 UTC
# RP/0/RP0/CPU0:ios#

# Using gathered to gather ACL facts from the device

- name: Gather ACL interfaces facts using gathered state
  cisco.iosxr.iosxr_acls:
    state: gathered

# Task Output (redacted)
# -----------------------
#

# "gathered": [
#    {
#        "acls": [
#            {
#                "aces": [
#                    {
#                        "remark": "TEST_ACL_1_REMARK",
#                        "sequence": 16
#                    },
#                    {
#                        "destination": {
#                            "address": "198.51.100.0",
#                            "wildcard_bits": "0.0.0.15"
#                        },
#                        "grant": "permit",
#                        "protocol": "tcp",
#                        "protocol_options": {
#                            "tcp": {
#                                "rst": true
#                            }
#                        },
#                        "sequence": 21,
#                        "source": {
#                            "host": "192.0.2.10",
#                            "port_protocol": {
#                                "range": {
#                                    "end": "121",
#                                    "start": "pop3"
#                                }
#                            }
#                        }
#                    },
#                    {
#                        "destination": {
#                            "address": "198.51.100.0",
#                            "wildcard_bits": "0.0.0.15"
#                        },
#                        "dscp": {
#                            "lt": "af12"
#                        },
#                        "grant": "deny",
#                        "protocol": "icmp",
#                        "protocol_options": {
#                            "icmp": {
#                                "reassembly_timeout": true
#                            }
#                        },
#                        "sequence": 23,
#                        "source": {
#                            "any": true
#                        }
#                    }
#                ],
#                "name": "acl_1"
#            },
#            {
#                "aces": [
#                    {
#                        "remark": "TEST_ACL_2_REMARK",
#                        "sequence": 10
#                    }
#                ],
#                "name": "acl_2"
#            }
#        ],
#        "afi": "ipv4"
#    },
#    {
#        "acls": [
#            {
#                "aces": [
#                    {
#                        "authen": true,
#                        "destination": {
#                            "any": true
#                        },
#                        "grant": "deny",
#                        "log": true,
#                        "protocol": "tcp",
#                        "protocol_options": {
#                            "tcp": {
#                                "syn": true
#                            }
#                        },
#                        "routing": true,
#                        "sequence": 10,
#                        "source": {
#                            "port_protocol": {
#                                "range": {
#                                   "end": "telnet",
#                                   "start": "ftp"
#                                }
#                            },
#                            "prefix": "2001:db8:1234::/48"
#                        },
#                        "ttl": {
#                            "range": {
#                                "end": 250,
#                                "start": 180
#                            }
#                        }
#                    },
#                    {
#                        "destination": {
#                            "any": true
#                        },
#                        "destopts": true,
#                        "grant": "permit",
#                        "precedence": "network",
#                        "protocol": "icmpv6",
#                        "protocol_options": {
#                            "icmpv6": {
#                                "router_advertisement": true
#                            }
#                        },
#                        "sequence": 20,
#                        "source": {
#                            "any": true
#                        }
#                    }
#                ],
#                "name": "acl6_1"
#            }
#        ],
#        "afi": "ipv6"
#    }
#  ]

# Using rendered

- name: Render platform specific commands (without connecting to the device)
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv4
      acls:
      - name: acl_2
        aces:
        - sequence: 11
          grant: permit
          protocol: igmp
          source:
            host: 198.51.100.130
          destination:
            any: true
          ttl:
            eq: 100

        - sequence: 12
          grant: deny
          source:
            any: true
          destination:
            any: true
          protocol: icmp
    state: rendered

# Task Output (redacted)
# -----------------------

# "rendered": [
#    "ipv4 access-list acl_2",
#    "11 permit igmp host 198.51.100.130 any ttl eq 100",
#    "12 deny icmp any any"

# Using parsed

# parsed.cfg
# ------------
#
# ipv4 access-list acl_1
#  10 remark TEST_ACL_2_REMARK
# ipv4 access-list acl_2
#  11 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 authen routing log
#  21 permit icmpv6 any any router-advertisement precedence network packet-length eq 576 destopts
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network packet-length eq 576 destopts

- name: Parse externally provided ACL config to agnostic model
  cisco.iosxr.iosxr_acls:
    running_config: "{{ lookup('file', 'parsed.cfg') }}"
    state: parsed

# Task Output (redacted)
# -----------------------
#  "parsed": [
#        {
#            "acls": [
#                {
#                    "aces": [
#                      {
#                            "remark": "TEST_ACL_2_REMARK",
#                            "sequence": 10
#                        }
#                    ],
#                   "name": "acl_1"
#                },
#                {
#                    "aces": [
#                        {
#                            "authen": true,
#                            "destination": {
#                                "any": true
#                            },
#                            "grant": "deny",
#                            "log": true,
#                            "protocol": "tcp",
#                            "protocol_options": {
#                                "tcp": {
#                                    "syn": true
#                                }
#                            },
#                            "routing": true,
#                            "sequence": 11,
#                            "source": {
#                                "port_protocol": {
#                                    "range": {
#                                        "end": "telnet",
#                                        "start": "ftp"
#                                    }
#                                },
#                                "prefix": "2001:db8:1234::/48"
#                            },
#                            "ttl": {
#                                "range": {
#                                    "end": 250,
#                                    "start": 180
#                                }
#                            }
#                        },
#                        {
#                            "destination": {
#                                "any": true
#                            },
#                            "destopts": true,
#                            "grant": "permit",
#                            "packet_length": {
#                                "eq": 576
#                            },
#                            "precedence": "network",
#                            "protocol": "icmpv6",
#                            "protocol_options": {
#                                "icmpv6": {
#                                    "router_advertisement": true
#                                }
#                            },
#                            "sequence": 21,
#                            "source": {
#                                "any": true
#                            }
#                        }
#                    ],
#                    "name": "acl_2"
#                }
#            ],
#            "afi": "ipv4"
#        },
#        {
#            "acls": [
#                {
#                    "aces": [
#                        {
#                            "authen": true,
#                            "destination": {
#                                "any": true
#                            },
#                            "grant": "deny",
#                            "log": true,
#                            "protocol": "tcp",
#                            "protocol_options": {
#                                "tcp": {
#                                    "syn": true
#                                }
#                            },
#                            "routing": true,
#                            "sequence": 10,
#                            "source": {
#                                "port_protocol": {
#                                    "range": {
#                                        "end": "telnet",
#                                        "start": "ftp"
#                                    }
#                                },
#                                "prefix": "2001:db8:1234::/48"
#                            },
#                            "ttl": {
#                                "range": {
#                                    "end": 250,
#                                    "start": 180
#                                }
#                            }
#                        },
#                        {
#                            "destination": {
#                                "any": true
#                            },
#                            "destopts": true,
#                            "grant": "permit",
#                            "packet_length": {
#                                "eq": 576
#                            },
#                            "precedence": "network",
#                            "protocol": "icmpv6",
#                            "protocol_options": {
#                                "icmpv6": {
#                                    "router_advertisement": true
#                                }
#                            },
#                            "sequence": 20,
#                            "source": {
#                                "any": true
#                            }
#                        }
#                    ],
#                    "name": "acl6_1"
#                }
#            ],
#            "afi": "ipv6"
#        }
#    ]

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
after list / elements=string	when changed	The resulting configuration model invocation. Sample: The configuration returned will always be in the same format of the parameters above.
before list / elements=string	always	The configuration prior to the model invocation. Sample: The configuration returned will always be in the same format of the parameters above.
commands list / elements=string	always	The set of commands pushed to the remote device. Sample: ['ipv6 access-list acl6_1', '10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 authen routing log', '20 permit icmpv6 any any router-advertisement precedence network destopts', 'ipv4 access-list acl_1', '16 remark TEST_ACL_1_REMARK', '21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst', '23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12']

Authors

Nilashish Chakraborty (@NilashishC)

© 2012–2018 Michael DeHaan
© 2018–2021 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.11/collections/cisco/iosxr/iosxr_acls_module.html