W3cubDocs

/Ansible 2.11

cisco.nxos.nxos_interface – (deprecated, removed after 2022-06-01) Manages physical attributes of interfaces.

Note

This plugin is part of the cisco.nxos collection (version 1.4.0).

To install it use: ansible-galaxy collection install cisco.nxos.

To use it in a playbook, specify: cisco.nxos.nxos_interface.

New in version 1.0.0: of cisco.nxos

DEPRECATED

Removed in

major release after 2022-06-01

Why

Updated modules released with more functionality

Alternative

nxos_interfaces

Synopsis

  • Manages physical attributes of interfaces of NX-OS switches.

Note

This module has a corresponding action plugin.

Parameters

Parameter Choices/Defaults Comments
admin_state
string
    Choices:
  • up
  • down
Administrative state of the interface.
aggregate
list / elements=dictionary
List of Interfaces definitions.
admin_state
string
    Choices:
  • up
  • down
Administrative state of the interface.
delay
integer
Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state arguments.
description
string
Interface description.
duplex
string
    Choices:
  • full
  • half
  • auto
Interface link status. Applicable for ethernet interface only.
fabric_forwarding_anycast_gateway
boolean
    Choices:
  • no
  • yes
Associate SVI with anycast gateway under VLAN configuration mode. Applicable for SVI interface only.
interface_type
string
    Choices:
  • loopback
  • portchannel
  • svi
  • nve
Interface type to be unconfigured from the device.
ip_forward
string
    Choices:
  • enable
  • disable
Enable/Disable ip forward feature on SVIs.
mode
string
    Choices:
  • layer2
  • layer3
Manage Layer 2 or Layer 3 state of the interface. This option is supported for ethernet and portchannel interface. Applicable for ethernet and portchannel interface only.
mtu
string
MTU for a specific interface. Must be an even number between 576 and 9216. Applicable for ethernet interface only.
name
string / required
Full name of interface, i.e. Ethernet1/1, port-channel10.
neighbors
list / elements=dictionary
Check the operational state of given interface name for LLDP neighbor.
The following suboptions are available. This is state check parameter only.
host
string
LLDP neighbor host for given interface name.
port
string
LLDP neighbor port to which given interface name is connected.
rx_rate
string
Receiver rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see Conditionals in Networking Modules
speed
string
Interface link speed. Applicable for ethernet interface only.
state
string
    Choices:
  • present
  • absent
  • default
Specify desired state of the resource.
tx_rate
string
Transmit rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see Conditionals in Networking Modules
delay
integer
Default:
10
Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state arguments.
description
string
Interface description.
duplex
string
    Choices:
  • full
  • half
  • auto
Interface link status. Applicable for ethernet interface only.
fabric_forwarding_anycast_gateway
boolean
    Choices:
  • no
  • yes
Associate SVI with anycast gateway under VLAN configuration mode. Applicable for SVI interface only.
interface_type
string
    Choices:
  • loopback
  • portchannel
  • svi
  • nve
Interface type to be unconfigured from the device.
ip_forward
string
    Choices:
  • enable
  • disable
Enable/Disable ip forward feature on SVIs.
mode
string
    Choices:
  • layer2
  • layer3
Manage Layer 2 or Layer 3 state of the interface. This option is supported for ethernet and portchannel interface. Applicable for ethernet and portchannel interface only.
mtu
string
MTU for a specific interface. Must be an even number between 576 and 9216. Applicable for ethernet interface only.
name
string
Full name of interface, i.e. Ethernet1/1, port-channel10.

aliases: interface
neighbors
list / elements=dictionary
Check the operational state of given interface name for LLDP neighbor.
The following suboptions are available. This is state check parameter only.
host
string
LLDP neighbor host for given interface name.
port
string
LLDP neighbor port to which given interface name is connected.
provider
dictionary
Deprecated
Starting with Ansible 2.5 we recommend using connection: network_cli.
Starting with Ansible 2.6 we recommend using connection: httpapi for NX-API.
This option will be removed in a release after 2022-06-01.
For more information please see the NXOS Platform Options guide.
A dict object containing connection details.
auth_pass
string
Specifies the password to use if required to enter privileged mode on the remote device. If authorize is false, then this argument does nothing. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_AUTH_PASS will be used instead.
authorize
boolean
    Choices:
  • no
  • yes
Instructs the module to enter privileged mode on the remote device before sending any commands. If not specified, the device will attempt to execute all commands in non-privileged mode. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_AUTHORIZE will be used instead.
host
string
Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
password
string
Specifies the password to use to authenticate the connection to the remote device. This is a common argument used for either cli or nxapi transports. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_PASSWORD will be used instead.
port
integer
Specifies the port to use when building the connection to the remote device. This value applies to either cli or nxapi. The port value will default to the appropriate transport common port if none is provided in the task. (cli=22, http=80, https=443).
ssh_keyfile
string
Specifies the SSH key to use to authenticate the connection to the remote device. This argument is only used for the cli transport. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_SSH_KEYFILE will be used instead.
timeout
integer
Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error. NX-API can be slow to return on long-running commands (sh mac, sh bgp, etc).
transport
string
    Choices:
  • cli
  • nxapi
Configures the transport connection to use when connecting to the remote device. The transport argument supports connectivity to the device over cli (ssh) or nxapi.
use_proxy
boolean
    Choices:
  • no
  • yes
If no, the environment variables http_proxy and https_proxy will be ignored.
use_ssl
boolean
    Choices:
  • no
  • yes
Configures the transport to use SSL if set to yes only when the transport=nxapi, otherwise this value is ignored.
username
string
Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate either the CLI login or the nxapi authentication depending on which transport is used. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_USERNAME will be used instead.
validate_certs
boolean
    Choices:
  • no
  • yes
If no, SSL certificates will not be validated. This should only be used on personally controlled sites using self-signed certificates. If the transport argument is not nxapi, this value is ignored.
rx_rate
string
Receiver rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see Conditionals in Networking Modules
speed
string
Interface link speed. Applicable for ethernet interface only.
state
string
    Choices:
  • present
  • absent
  • default
Specify desired state of the resource.
tx_rate
string
Transmit rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see Conditionals in Networking Modules

Notes

Note

  • Tested against NXOSv 7.3.(0)D1(1) on VIRL
  • This module is also used to create logical interfaces such as svis and loopbacks.
  • Be cautious of platform specific idiosyncrasies. For example, when you default a loopback interface, the admin state toggles on certain versions of NX-OS.
  • The cisco.nxos.nxos_overlay_global anycast_gateway_mac attribute must be set before setting the fabric_forwarding_anycast_gateway property.
  • For information on using CLI and NX-API see the NXOS Platform Options guide
  • For more information on using Ansible to manage network devices see the Ansible Network Guide
  • For more information on using Ansible to manage Cisco devices see the Cisco integration page.

Examples

- name: Ensure an interface is a Layer 3 port and that it has the proper description
  cisco.nxos.nxos_interface:
    name: Ethernet1/1
    description: Configured by Ansible
    mode: layer3

- name: Admin down an interface
  cisco.nxos.nxos_interface:
    name: Ethernet2/1
    admin_state: down

- name: Remove all loopback interfaces
  cisco.nxos.nxos_interface:
    name: loopback
    state: absent

- name: Remove all logical interfaces
  cisco.nxos.nxos_interface:
    interface_type: '{{ item }} '
    state: absent
  loop:
  - loopback
  - portchannel
  - svi
  - nve

- name: Admin up all loopback interfaces
  cisco.nxos.nxos_interface:
    name: loopback 0-1023
    admin_state: up

- name: Admin down all loopback interfaces
  cisco.nxos.nxos_interface:
    name: loopback 0-1023
    admin_state: down

- name: Check neighbors intent arguments
  cisco.nxos.nxos_interface:
    name: Ethernet2/3
    neighbors:
    - port: Ethernet2/3
      host: abc.mycompany.com

- name: Add interface using aggregate
  cisco.nxos.nxos_interface:
    aggregate:
    - {name: Ethernet0/1, mtu: 256, description: test-interface-1}
    - {name: Ethernet0/2, mtu: 516, description: test-interface-2}
    duplex: full
    speed: 100
    state: present

- name: Delete interface using aggregate
  cisco.nxos.nxos_interface:
    aggregate:
    - name: Loopback9
    - name: Loopback10
    state: absent

- name: Check intent arguments
  cisco.nxos.nxos_interface:
    name: Ethernet0/2
    state: up
    tx_rate: ge(0)
    rx_rate: le(0)

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
commands
list / elements=string
always
command list sent to the device

Sample:
['interface Ethernet2/3', 'mtu 1500', 'speed 10']


Status

  • This module will be removed in a major release after 2022-06-01. [deprecated]
  • For more information see DEPRECATED.

Authors

  • Jason Edelman (@jedelman8)
  • Trishna Guha (@trishnaguha)

© 2012–2018 Michael DeHaan
© 2018–2021 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.11/collections/cisco/nxos/nxos_interface_module.html