W3cubDocs

/Ansible 2.11

junipernetworks.junos.junos_interface – (deprecated, removed after 2022-06-01) Manage Interface on Juniper JUNOS network devices

Note

This plugin is part of the junipernetworks.junos collection (version 1.3.0).

To install it use: ansible-galaxy collection install junipernetworks.junos.

To use it in a playbook, specify: junipernetworks.junos.junos_interface.

New in version 1.0.0: of junipernetworks.junos

DEPRECATED
Synopsis
Requirements
Parameters
Notes
Examples
Return Values
Status

DEPRECATED

Removed in: major release after 2022-06-01
Why: Updated modules released with more functionality
Alternative: Use junipernetworks.junos.junos_interfaces instead.

Synopsis

This module provides declarative management of Interfaces on Juniper JUNOS network devices.

Note

This module has a corresponding action plugin.

Requirements

The below requirements are needed on the host that executes this module.

ncclient (>=v0.5.2)

Parameters

Parameter			Choices/Defaults	Comments
active boolean			Choices: no yes ←	Specifies whether or not the configuration is active or deactivated
aggregate list / elements=dictionary				List of Interfaces definitions.
	active boolean		Choices: no yes	Specifies whether or not the configuration is active or deactivated
	delay integer			Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values `up`/`down`, tx_rate and rx_rate.
	description string			Description of Interface.
	duplex string		Choices: full half auto	Interface link status.
	enabled boolean		Choices: no yes	Configure interface link status.
	mtu integer			Maximum size of transmit packet.
	name string / required			Name of the Interface.
	neighbors list / elements=dictionary			Check the operational state of given interface `name` for LLDP neighbor. The following suboptions are available.
		host string		LLDP neighbor host for given interface `name`.
		port string		LLDP neighbor port to which given interface `name` is connected.
	rx_rate string			Receiver rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
	speed string			Interface link speed.
	state string		Choices: present absent up down	State of the Interface configuration, `up` indicates present and operationally up and `down` indicates present and operationally `down`
	tx_rate string			Transmit rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
delay integer			Default: 10	Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values `up`/`down`, tx_rate and rx_rate.
description string				Description of Interface.
duplex string			Choices: full half auto	Interface link status.
enabled boolean			Choices: no yes ←	Configure interface link status.
mtu integer				Maximum size of transmit packet.
name string				Name of the Interface.
neighbors list / elements=dictionary				Check the operational state of given interface `name` for LLDP neighbor. The following suboptions are available.
	host string			LLDP neighbor host for given interface `name`.
	port string			LLDP neighbor port to which given interface `name` is connected.
provider dictionary				Deprecated Starting with Ansible 2.5 we recommend using `connection: network_cli` or `connection: netconf`. For more information please see the Junos OS Platform Options guide. A dict object containing connection details.
	host string			Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
	password string			Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_PASSWORD` will be used instead.
	port integer			Specifies the port to use when building the connection to the remote device. The port value will default to the well known SSH port of 22 (for `transport=cli`) or port 830 (for `transport=netconf`) device.
	ssh_keyfile path			Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_SSH_KEYFILE` will be used instead.
	timeout integer			Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
	transport string		Choices: cli netconf ←	Configures the transport connection to use when connecting to the remote device.
	username string			Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_USERNAME` will be used instead.
rx_rate string				Receiver rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
speed string				Interface link speed.
state string			Choices: present ← absent up down	State of the Interface configuration, `up` indicates present and operationally up and `down` indicates present and operationally `down`
tx_rate string				Transmit rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules

Notes

Note

This module requires the netconf system service be enabled on the remote device being managed.
Tested against vSRX JUNOS version 15.1X49-D15.4, vqfx-10000 JUNOS Version 15.1X53-D60.4.
Recommended connection is netconf. See the Junos OS Platform Options.
This module also works with local connections for legacy playbooks.
For information on using CLI and netconf see the Junos OS Platform Options guide
For more information on using Ansible to manage network devices see the Ansible Network Guide
For more information on using Ansible to manage Juniper network devices see https://www.ansible.com/ansible-juniper.

Examples

- name: configure interface
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    description: test-interface

- name: remove interface
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    state: absent

- name: make interface down
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    enabled: false

- name: make interface up
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    enabled: true

- name: Deactivate interface config
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    state: present
    active: false

- name: Activate interface config
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    state: present
    active: true

- name: Configure interface speed, mtu, duplex
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    state: present
    speed: 1g
    mtu: 256
    duplex: full

- name: Create interface using aggregate
  junipernetworks.junos.junos_interface:
    aggregate:
    - name: ge-0/0/1
      description: test-interface-1
    - name: ge-0/0/2
      description: test-interface-2
    speed: 1g
    duplex: full
    mtu: 512

- name: Delete interface using aggregate
  junipernetworks.junos.junos_interface:
    aggregate:
    - name: ge-0/0/1
    - name: ge-0/0/2
    state: absent

- name: Check intent arguments
  junipernetworks.junos.junos_interface:
    name: '{{ name }}'
    state: up
    tx_rate: ge(0)
    rx_rate: le(0)

- name: Check neighbor intent
  junipernetworks.junos.junos_interface:
    name: xe-0/1/1
    neighbors:
    - port: Ethernet1/0/1
      host: netdev

- name: Config + intent
  junipernetworks.junos.junos_interface:
    name: '{{ name }}'
    enabled: false
    state: down

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
diff.prepared string	when configuration is changed and diff option is enabled.	Configuration difference before and after applying change. Sample: [edit interfaces] + ge-0/0/1 { + description test-interface; + }

Status

This module will be removed in a major release after 2022-06-01. [deprecated]
For more information see DEPRECATED.

Authors

Ganesh Nalawade (@ganeshrn)

© 2012–2018 Michael DeHaan
© 2018–2021 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.11/collections/junipernetworks/junos/junos_interface_module.html