W3cubDocs

/Terraform

aws_default_network_acl

Provides a resource to manage the default AWS Network ACL. VPC Only.

Each VPC created in AWS comes with a Default Network ACL that can be managed, but not destroyed. This is an advanced resource, and has special caveats to be aware of when using it. Please read this document in its entirety before using this resource.

The aws_default_network_acl behaves differently from normal resources, in that Terraform does not create this resource, but instead attempts to "adopt" it into management. We can do this because each VPC created has a Default Network ACL that cannot be destroyed, and is created with a known set of default rules.

When Terraform first adopts the Default Network ACL, it immediately removes all rules in the ACL. It then proceeds to create any rules specified in the configuration. This step is required so that only the rules specified in the configuration are created.

This resource treats its inline rules as absolute; only the rules defined inline are created, and any additions/removals external to this resource will result in diffs being shown. For these reasons, this resource is incompatible with the aws_network_acl_rule resource.

For more information about Network ACLs, see the AWS Documentation on Network ACLs.

Basic Example Usage, with default rules

The following config gives the Default Network ACL the same rules that AWS includes, but pulls the resource under management by Terraform. This means that any ACL rules added or changed will be detected as drift.

resource "aws_vpc" "mainvpc" {
  cidr_block = "10.1.0.0/16"
}

resource "aws_default_network_acl" "default" {
  default_network_acl_id = "${aws_vpc.mainvpc.default_network_acl_id}"

  ingress {
    protocol   = -1
    rule_no    = 100
    action     = "allow"
    cidr_block = "0.0.0.0/0"
    from_port  = 0
    to_port    = 0
  }

  egress {
    protocol   = -1
    rule_no    = 100
    action     = "allow"
    cidr_block = "0.0.0.0/0"
    from_port  = 0
    to_port    = 0
  }
}

Example config to deny all Egress traffic, allowing Ingress

The following denies all Egress traffic by omitting any egress rules, while including the default ingress rule to allow all traffic.

resource "aws_vpc" "mainvpc" {
  cidr_block = "10.1.0.0/16"
}

resource "aws_default_network_acl" "default" {
  default_network_acl_id = "${aws_vpc.mainvpc.default_network_acl_id}"

  ingress {
    protocol   = -1
    rule_no    = 100
    action     = "allow"
    cidr_block = "0.0.0.0/0"
    from_port  = 0
    to_port    = 0
  }
}

Example config to deny all traffic to any Subnet in the Default Network ACL:

This config denies all traffic in the Default ACL. This can be useful if you want a locked down default to force all resources in the VPC to assign a non-default ACL.

resource "aws_vpc" "mainvpc" {
  cidr_block = "10.1.0.0/16"
}

resource "aws_default_network_acl" "default" {
  default_network_acl_id = "${aws_vpc.mainvpc.default_network_acl_id}"

  # no rules defined, deny all traffic in this ACL
}

Argument Reference

The following arguments are supported:

  • default_network_acl_id - (Required) The Network ACL ID to manage. This attribute is exported from aws_vpc, or manually found via the AWS Console.
  • subnet_ids - (Optional) A list of Subnet IDs to apply the ACL to. See the notes below on managing Subnets in the Default Network ACL
  • ingress - (Optional) Specifies an ingress rule. Parameters defined below.
  • egress - (Optional) Specifies an egress rule. Parameters defined below.
  • tags - (Optional) A mapping of tags to assign to the resource.

Both egress and ingress support the following keys:

  • from_port - (Required) The from port to match.
  • to_port - (Required) The to port to match.
  • rule_no - (Required) The rule number. Used for ordering.
  • action - (Required) The action to take.
  • protocol - (Required) The protocol to match. If using the -1 'all' protocol, you must specify a from and to port of 0.
  • cidr_block - (Optional) The CIDR block to match. This must be a valid network mask.
  • ipv6_cidr_block - (Optional) The IPv6 CIDR block.
  • icmp_type - (Optional) The ICMP type to be used. Default 0.
  • icmp_code - (Optional) The ICMP type code to be used. Default 0.

Managing Subnets in the Default Network ACL

Within a VPC, all Subnets must be associated with a Network ACL. In order to "delete" the association between a Subnet and a non-default Network ACL, the association is destroyed by replacing it with an association between the Subnet and the Default ACL instead.

When managing the Default Network ACL, you cannot "remove" Subnets. Instead, they must be reassigned to another Network ACL, or the Subnet itself must be destroyed. Because of these requirements, removing the subnet_ids attribute from the configuration of a aws_default_network_acl resource may result in a reoccurring plan, until the Subnets are reassigned to another Network ACL or are destroyed.

Because Subnets are by default associated with the Default Network ACL, any non-explicit association will show up as a plan to remove the Subnet. For example: if you have a custom aws_network_acl with two subnets attached, and you remove the aws_network_acl resource, after successfully destroying this resource future plans will show a diff on the managed aws_default_network_acl, as those two Subnets have been orphaned by the now destroyed network acl and thus adopted by the Default Network ACL. In order to avoid a reoccurring plan, they will need to be reassigned, destroyed, or added to the subnet_ids attribute of the aws_default_network_acl entry.

Removing aws_default_network_acl from your configuration

Each AWS VPC comes with a Default Network ACL that cannot be deleted. The aws_default_network_acl allows you to manage this Network ACL, but Terraform cannot destroy it. Removing this resource from your configuration will remove it from your statefile and management, but will not destroy the Network ACL. All Subnets associations and ingress or egress rules will be left as they are at the time of removal. You can resume managing them via the AWS Console.

Attributes Reference

In addition to all arguments above, the following attributes are exported:

  • id - The ID of the Default Network ACL
  • vpc_id - The ID of the associated VPC
  • ingress - Set of ingress rules
  • egress - Set of egress rules
  • subnet_ids – IDs of associated Subnets

© 2018 HashiCorpLicensed under the MPL 2.0 License.
https://www.terraform.io/docs/providers/aws/r/default_network_acl.html