W3cubDocs

/Ansible 2.9

icx_l3_interface – Manage Layer-3 interfaces on Ruckus ICX 7000 series switches

New in version 2.9.

Synopsis

  • This module provides declarative management of Layer-3 interfaces on ICX network devices.

Parameters

Parameter Choices/Defaults Comments
aggregate
list
List of Layer-3 interfaces definitions. Each of the entry in aggregate list should define name of interface name and a optional ipv4 or ipv6 address.
check_running_config
boolean
    Choices:
  • no
  • yes
Check running configuration. This can be set as environment variable. Module will use environment variable value(default:True), unless it is overridden, by specifying it as module parameter.
ipv4
string
IPv4 address to be set for the Layer-3 interface mentioned in name option. The address format is <ipv4 address>/<mask>, the mask is number in range 0-32 eg. 192.168.0.1/24
ipv6
string
IPv6 address to be set for the Layer-3 interface mentioned in name option. The address format is <ipv6 address>/<mask>, the mask is number in range 0-128 eg. fd5d:12c9:2201:1::1/64.
mode
string
    Choices:
  • dynamic
  • ospf-ignore
  • ospf-passive
Specifies if ipv4 address should be dynamic/advertise to ospf/not advertise to ospf. This should be specified only if ipv4 address is configured and if it is not secondary IP address.
name
string
Name of the Layer-3 interface to be configured eg. GigabitEthernet0/2, ve 10, ethernet 1/1/1
replace
string
    Choices:
  • yes
  • no
Replaces the configured primary IP address on the interface.
secondary
string
    Choices:
  • yes
  • no
Specifies that the configured address is a secondary IP address. If this keyword is omitted, the configured address is the primary IP address.
state
string
    Choices:
  • present
  • absent
State of the Layer-3 interface configuration. It indicates if the configuration should be present or absent on remote device.
check_running_config
boolean
    Choices:
  • no
  • yes
Check running configuration. This can be set as environment variable. Module will use environment variable value(default:True), unless it is overridden, by specifying it as module parameter.
ipv4
string
IPv4 address to be set for the Layer-3 interface mentioned in name option. The address format is <ipv4 address>/<mask>, the mask is number in range 0-32 eg. 192.168.0.1/24
ipv6
string
IPv6 address to be set for the Layer-3 interface mentioned in name option. The address format is <ipv6 address>/<mask>, the mask is number in range 0-128 eg. fd5d:12c9:2201:1::1/64.
mode
string
    Choices:
  • dynamic
  • ospf-ignore
  • ospf-passive
Specifies if ipv4 address should be dynamic/advertise to ospf/not advertise to ospf. This should be specified only if ipv4 address is configured and if it is not secondary IP address.
name
string
Name of the Layer-3 interface to be configured eg. GigabitEthernet0/2, ve 10, ethernet 1/1/1
replace
string
    Choices:
  • yes
  • no
Replaces the configured primary IP address on the interface.
secondary
string
    Choices:
  • yes
  • no
Specifies that the configured address is a secondary IP address. If this keyword is omitted, the configured address is the primary IP address.
state
string
    Choices:
  • present
  • absent
State of the Layer-3 interface configuration. It indicates if the configuration should be present or absent on remote device.

Notes

Note

Examples

- name: Remove ethernet 1/1/1 IPv4 and IPv6 address
  icx_l3_interface:
    name: ethernet 1/1/1
    ipv4: 192.168.0.1/24
    ipv6: "fd5d:12c9:2201:1::1/64"
    state: absent

- name: Replace ethernet 1/1/1 primary IPv4 address
  icx_l3_interface:
    name: ethernet 1/1/1
    ipv4: 192.168.0.1/24
    replace: yes
    state: absent

- name: Replace ethernet 1/1/1 dynamic IPv4 address
  icx_l3_interface:
    name: ethernet 1/1/1
    ipv4: 192.168.0.1/24
    mode: dynamic
    state: absent

- name: Set ethernet 1/1/1 secondary IPv4 address
  icx_l3_interface:
    name: ethernet 1/1/1
    ipv4: 192.168.0.1/24
    secondary: yes
    state: absent

- name: Set ethernet 1/1/1 IPv4 address
  icx_l3_interface:
    name: ethernet 1/1/1
    ipv4: 192.168.0.1/24

- name: Set ethernet 1/1/1 IPv6 address
  icx_l3_interface:
    name: ethernet 1/1/1
    ipv6: "fd5d:12c9:2201:1::1/64"

- name: Set IP addresses on aggregate
  icx_l3_interface:
    aggregate:
      - { name: GigabitEthernet0/3, ipv4: 192.168.2.10/24 }
      - { name: GigabitEthernet0/3, ipv4: 192.168.3.10/24, ipv6: "fd5d:12c9:2201:1::1/64" }

- name: Remove IP addresses on aggregate
  icx_l3_interface:
    aggregate:
      - { name: GigabitEthernet0/3, ipv4: 192.168.2.10/24 }
      - { name: GigabitEthernet0/3, ipv4: 192.168.3.10/24, ipv6: "fd5d:12c9:2201:1::1/64" }
    state: absent


- name: Set the ipv4 and ipv6 of a virtual ethernet(ve)
  icx_l3_interface:
    name: ve 100
    ipv4: 192.168.0.1
    ipv6: "2001:0db8:85a3:0000:0000:8a2e:0370:7334"

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
commands
list
always, except for the platforms that use Netconf transport to manage the device.
The list of configuration mode commands to send to the device

Sample:
['interface ethernet 1/1/1', 'ip address 192.168.0.1 255.255.255.0', 'ipv6 address fd5d:12c9:2201:1::1/64']


Status

Authors

  • Ruckus Wireless (@Commscope)

Hint

If you notice any issues in this documentation, you can edit this document to improve it.

© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.9/modules/icx_l3_interface_module.html